Questions tagged [packages]
In electronics packages refer to the physical encapsulation of a device. Most package names are standardized, so for example a TO-92 package will have similar dimensions and pin spacing between manufacturers so the same PCB footprint may be used. Be aware however many packages have subtle variations, for example TO-206AA, TO-206AB and TO-206AC.
286
questions
0
votes
2
answers
108
views
Is VSSOP-8 packaging any different from SOP-8?
Are these two packaging titles similar with different names or is there actually a difference?
(please provide both sizes in mils if different)
The device in question is a INA821
9
votes
1
answer
19k
views
What is the difference between TO-220F and TO-220FP cases?
Google search results imply TO-220FP to be full-pack case.
Wikipedia says that TO-220F is full-pack case.
Farnell categorizes TO-220F and TO-22FP differently.
I'm confused. What is the difference ...
1
vote
1
answer
53
views
I need to identify a component package and, if possible, the component
I need to know haw the package and/or the component of the picture. It is between the VCC supply voltage and the voltage that goes to the rest of the circuit. Apparently it does not behave like a ...
0
votes
1
answer
95
views
Are these old graphic controllers all the same die packaged by different manufacturers? [closed]
I am looking at old ISA graphic adapters that would provide a simple black and white text mode. I am trying to make the design as simple as possible and I would like to make the PCB as small as ...
0
votes
0
answers
59
views
decoding the symbols of the Abracon series ASTMLP marking
I purchased the ASTMLPE-100,000MHZ-L JET component. I would like to figure out what is encrypted in the component labeling.
0
votes
0
answers
55
views
Pins in standard part supporting multiple packages not connected
I have two parts on my board that each support multiple packakes so that it easier to find a fitting part. Both are taken from the libraries that came with eagle
a potentiometer: TRIM_1234-S64YW (...
0
votes
2
answers
74
views
How does a "high" current switching regulator/converter handle such high current with such a small package?
The package of this converter is very small but it aparently can handle 24A.
Vishay SiC431 3 V to 24 V Input, 24 A microBUCK ® DC/DC Converter
It does not make sense to me with a pin width of 0.3mm. ...
1
vote
2
answers
57
views
Is IC power pin position (V+ / V-) for a package mostly standardized for opamps, comparators, INAs etc.?
Is the power pin position for certain types of ICs standardized or practically, mostly standard? I assume there are rare exceptions and manufacturers could do what they want, but the general answer to ...
1
vote
1
answer
244
views
What is this DFN 8-pin package?
Can anyone identify this 8-pin DFN SMD component?
Marking is:
LAAS
N819
417
5
votes
3
answers
3k
views
Can dual BJT packages be reliably used as current mirrors?
If I need current mirrors, can I just use dual NPN packages? I know that if multiple BJTs are manufactured on one die, they can pretty much be guaranteed to have the same spread.
Should I just stay ...
2
votes
0
answers
34
views
Looking for a solution to tape and reeling 01005 components
Current tape and reel causes 01005 size components to move around. How can I have them packaged so they can retain their original orientation?
I've spoken to many reeling houses, any feedback is ...
15
votes
7
answers
5k
views
Tradeoffs when choosing the op-amp package: quad vs dual vs single
Let's say as an example that I need to use four op-amps in my project. I don't have any super strict requirement of space and price.
Which are the parameters to take into account when choosing the ...
4
votes
2
answers
433
views
Why do some through-hole LEDs have flared leads? [duplicate]
I have worked with many through-hole LEDs over the years. I ordered a bunch for a personal project. I did not notice until I went to solder them onto a PCB that the leads could not be inserted the ...
1
vote
2
answers
78
views
How to open hermetic TO packages?
I would like to open a TO-18 can to look at die-bonding/heatsinking and do some electrical experiments with increased airflow. Is there a non-destructive way to do this?
My only thought is to drill a ...
1
vote
2
answers
255
views
Pin numbering of FPC1020AP chip
I have a single FPC1020AP chip as shown in the picture below. The datasheet for FPC1020 says there are 19 pins, of which 15 are used. However, I cannot find the datasheet for this exact chip, which ...