Questions tagged [packages]
In electronics packages refer to the physical encapsulation of a device. Most package names are standardized, so for example a TO-92 package will have similar dimensions and pin spacing between manufacturers so the same PCB footprint may be used. Be aware however many packages have subtle variations, for example TO-206AA, TO-206AB and TO-206AC.
25
questions with no upvoted or accepted answers
4
votes
0
answers
333
views
What should I do with the unused diode in the SOT-323-3 (SC-70-3) package?
I'm planning to use one of this diode in my circuit. But the package contains two of them. I chose it mainly because of its 3ns reverse recovery time. How do I use them in my circuit?
I have three ...
2
votes
0
answers
34
views
Looking for a solution to tape and reeling 01005 components
Current tape and reel causes 01005 size components to move around. How can I have them packaged so they can retain their original orientation?
I've spoken to many reeling houses, any feedback is ...
2
votes
1
answer
121
views
What's the purpose of these copper tracks on the bottom of BGA package?
These are STM32F746NGH6 microcontroller chips in .8 mm pitch BGA package. I noticed that there are copper tracks on the bottom of this chip, some of which lead to the edge of the chip and are left ...
2
votes
0
answers
448
views
IC package reliability with physical stress
One of the ICs for my design comes in LQFP, TSSOP, QFN and even WLCSP packages. I don't care about the footprint, and the only thing that I want to maximize with the package choice is reliability ...
1
vote
2
answers
57
views
Is IC power pin position (V+ / V-) for a package mostly standardized for opamps, comparators, INAs etc.?
Is the power pin position for certain types of ICs standardized or practically, mostly standard? I assume there are rare exceptions and manufacturers could do what they want, but the general answer to ...
1
vote
0
answers
50
views
MOSFET SOA: Isn't the package current limit-line ambient temperature dependent?
Ref 1 says "The package limit-line will not change in case application conditions such as ambient
temperature vary"
As explained in Ref2, this limit is due to bond wire heating/melting.
If ...
1
vote
0
answers
54
views
Has any implementation succeeded to have shared key inside chipset and protect it from exploits?
Since there is a lot of demonstration like using SEM (Scanning Electron Microscope) to read bits from ROM through the scanned image of chipset, is there any implementation that has managed to succeed ...
1
vote
0
answers
1k
views
How to read data from Agilent 34401a using GPIB-USB-B connection
I want to read data from an Agilent 34401a DMM directly into python or matlab so the data can be automatically recorded. However, I can't seem to make the connection. On my computer the device is ...
1
vote
0
answers
323
views
Electronics components casing or packaging style types and diferences?
Is there any good visual guide or reference that explains the different types of casing styles like these ones that I come across every time I try to buy a component on farnell website:
...
1
vote
0
answers
157
views
chip resistor/capacitor size vs performance for analog circuits
I am designing one four layer ADS1298 (TI) based analog PCB. Signal frequency is about 1.5Hz to 3.79kHz. It is a four layer board with most of the components and traces on top layer and the ground ...
1
vote
0
answers
218
views
What is the difference between red glass diodes and blue glass diodes?
I have some old hermetically sealed glass diodes that have a blue color under the glass, which is different from the red ones that I normally see. Does anybody know what the difference between the red ...
1
vote
0
answers
57
views
placing hermetical packages on PCB and soldering
I stumbled upon some hermetically enclosed packaged - Link.
The package has a small bulge/projection on the bottom. This makes the package leads basically float without contact with the PCB. How do we ...
1
vote
0
answers
127
views
Eagle: IC package variant, different pins bonded out
I'm trying to create an Eagle component for the Altera EP4CE22, which comes in BGA and SMD packages, where different pins are actually available on the outside of the package.
Is it possible to reuse ...
0
votes
0
answers
59
views
decoding the symbols of the Abracon series ASTMLP marking
I purchased the ASTMLPE-100,000MHZ-L JET component. I would like to figure out what is encrypted in the component labeling.
0
votes
0
answers
55
views
Pins in standard part supporting multiple packages not connected
I have two parts on my board that each support multiple packakes so that it easier to find a fitting part. Both are taken from the libraries that came with eagle
a potentiometer: TRIM_1234-S64YW (...