Questions tagged [ltspice]
Anything related to LTspice. LTspice is a SPICE simulation, schematic capture, and waveform viewer program from Linear Technology. LTspice is freeware with a very liberal license, it is lightweight, and isn't crippled in any way.
2,374
questions
3
votes
1
answer
192
views
LT6268-10 Opamp Oscillation and Offset
Below is my Photodiode-OpAmp circuit that is configured as Transimpedance Amplifier.
When I put both inverting and non inverting into ground, no signal is coming out. However when I connect ...
0
votes
1
answer
70
views
Modelling power transfer under saturation for 1:N current transformer in LTspice
A toroidal current transformer consisting of two half-toroids with air gaps, is clamped around an overhead 50 Hz AC power line carrying 50-300 A (i.e. a 1:N CT). It is used for energy harvesting.
Is ...
0
votes
1
answer
66
views
Help to configure an LTspice PLL simulation
I never tried PLLs before and to gain some insight I'm trying to simulate CD4046Bg in LTspice where I want the output to phase-lock and follow the input signal. I tried so far the below:
But I get an ...
0
votes
1
answer
53
views
Import transistor into LTSpice
I would like to import this transistor -> RFD16N06LE (datasheet: https://www.alldatasheet.com/datasheet-pdf/pdf/67811/INTERSIL/RFD16N06LE.html) into LTSpice; the datasheet has a PSPICE model ...
1
vote
3
answers
86
views
Decent MOSFET for a beginner to learn from?
I am relearning MOSFETs, but more importantly I would like to focus on building some basic circuits and learning practicality over theory. I have a BSEE but haven't spent much time outside of class on ...
2
votes
0
answers
32
views
Where should I take the measurement from to find the correct attenuation level of a resistive pi attenuator?
I am currently designing a resistive attenuator for an RF project I'm working on. I wanted to have several resistance combinations to obtain various attenuation levels (1-8 dBs). When I calculate the ...
1
vote
0
answers
58
views
Can this oscillator possibly work?
I am trying to build a crude RF oscillator. My first attempt, though it simulated fine, disappointingly did not oscillate when soldered together. So, to debug this, I reduced the simulation example ...
0
votes
1
answer
46
views
How can I simulate an RF signal as received by an antenna in LTspice?
How can I simulate an RF signal as received by an antenna in LTspice?
I am designing a simple HF RF receiver and want to test it via LTspice. Can I simulate an RF signal as:
A pure voltage source, ...
-1
votes
0
answers
48
views
How soft start circuit works, LTspice simulation [closed]
Please help for the attached circuit, further explain how soft start circuit works in M2 (PMOS) with RC circuit, computation and the voltage divider with zener diode with BJT (PNP), how it works, for ...
2
votes
1
answer
103
views
Why did I get different simulation results for the same transistor model in LTspice?
The following is my FM transmitter circuit. In the first simulation, I auto-generated a symbol for BFQ19S.
Replace the auto-generated symbol with the one from default NPN.
In the second simulation, ...
-2
votes
1
answer
109
views
Is there any way to speed up simulation in Ltspice? [closed]
The following is my FM transmitter circuit. It takes about 1 minute to simulate.
In real life, I want to use this BFQ19SH6327XTSA1 from Infineon instead of 2N22222. (link datasheet) and download link ...
1
vote
2
answers
64
views
Beat frequency - Square signal
This question comes from this one, LTspice - Beat frequency:
It appears that when I did a FFT of two sinusoidal signals, there was no what is called beat frequency.
When I do the same exercice with ...
0
votes
1
answer
95
views
Does the FFT in LTspice not work properly?
I wanted to do an FFT of a square signal in LTspice. Here is the simulation:
Here is the result of the FFT through R4:
There is no reason to have frequencies below 100 kHz according to theory. What ...
1
vote
3
answers
101
views
LTspice - Beat frequency
Here is the theory from wikipedia:
Here are my summation of sin on LTspice:
The frequencies are 100 kHz and 120 kHz on the FFT. There is no frequencies at (f1+f2)/2 and no frequencies at (f1-f2)/2.
...
1
vote
0
answers
52
views
Need help analyzing sability of op-amp in a current source in LTSpice
I have to perform stability analysis on an op-amp (AD8671) which is being used as an op-amp in the circuit attached. I am using LTSpice to perform this. My approach is to give a 1V AC small signal at ...
2
votes
1
answer
53
views
I am Seeking Help to Adjust DC Motor Simulation Parameters in LTspice for Accurate Current Modeling
I'm relatively new to LTspice and motor diagnostics, but I have managed to build a PWM-MOSFET control circuit for a DC motor. My goal is to simulate this project to evaluate potential ripple currents ...
-1
votes
2
answers
65
views
LTspice simulating varying capacitance in cap-to-voltage simulation [closed]
I am interested in simulating the increasing output voltage and the end of this circuit when the parameter C1, changes according to a list of increasing capacitance values. So far I have managed to ...
1
vote
1
answer
58
views
How does the leakage inductor distribute over multiple coupled inductors?
I am working in LTspice with a triple coupled magnetic inductor. I chose the factor of coupling to be 90%. L_1 is 1000uH so the uncoupled energy should be 100uH. How does the 100uH energy distribute ...
0
votes
1
answer
49
views
Iterative Simulation LTspice Model using Python
I'm new to python. I have a python code to simulate my LTspice model. I need to change the on time in the pulse parameters and I need a large number of simulations for at least 100 different Ton. So I ...
1
vote
1
answer
49
views
How to simulate a uniform distribution around zero in LTSpice?
I am using LTSpice for a Monte-Carlo simulation, I typically use the function {mc(x,y)} for componant variability
I also want to introduce spread in the feedback ...
-2
votes
0
answers
35
views
LTSpice old GUI schematic icons
This is about LTSpice version 24.0.12
How to get the hand symbol (move) back in new GUI? I would like the icon refer to something real worldy. A hand is used universally for moving things and current ...
2
votes
1
answer
79
views
Pi-Filter Simulations Comparison
I am trying to simulate the filter impedances on LTspice. There are two images of the simulation results of the same pi-filter on LTspice and Redexpert. Although I am not sure the parameters are ...
0
votes
0
answers
41
views
How can I determine how much power is in a frequency range via FFT in LTspice?
When using LTspice, I can see the FFT of a voltage. How can I see how much power is in a particular frequency band, and what portion of the total power it is?
The FFT in LTspice is in dB, but it's ...
0
votes
1
answer
57
views
Non buffered CMOS logic gates working under load when using real components (LTSpice Sim)?
I'm experimenting with CMOS logic gates and have encountered something I am having a hard time understanding.
When I make an inverter using ideal components and measure the output, it works exactly as ...
0
votes
0
answers
41
views
3 phase inverter with IR2110 LTspice
I am trying to implement a 3 phase inverter using IR2110 (model downloaded from infineon website) as gate drivers. I have tried to simulate the circuit using LTspice but I am having some issues.
This ...
0
votes
1
answer
60
views
How can i check what pin is configured to what netlist order from the SPICE model?
I am trying to make a model for an op-amp (AD8000) in LT SPICE. So far here is what i did:
First I downloaded the model from https://www.analog.com/en/products/ad8000.html
and opened it from my ...
1
vote
1
answer
56
views
Why does LTC6253-7 not perform properly on LTspice?
I am working with LTC6253-7 op amp which should have a bandwidth of 2 GHz but when I simulate the output for a follower and the output is being severely attenuated. Is there a technique that must be ...
0
votes
1
answer
41
views
What is this pin for on LTC6253-7 [closed]
I have tried looking at the datasheet but can't seem to find any information on this pin.
0
votes
0
answers
22
views
How to stimulate PSRR of LT3060-2.5 and LT1761-2.5 in LTspice?
I tried following the steps on the analog devices website but it seems that with these components the results are not close to the datasheet while when I try this method with others it works.
Do you ...
-1
votes
1
answer
81
views
Are there any LTspice models for OP AMPS with GHz bandwidth? [closed]
I would like to try experimenting with op amps to use as buffers for oscillators. I know op amps exist for such applications because I have found them but none of them have LTspice models. Let me know ...