Questions tagged [leakage]
The leakage tag has no usage guidance.
13
questions
1
vote
1
answer
58
views
How does the leakage inductor distribute over multiple coupled inductors?
I am working in LTspice with a triple coupled magnetic inductor. I chose the factor of coupling to be 90%. L_1 is 1000uH so the uncoupled energy should be 100uH. How does the 100uH energy distribute ...
1
vote
2
answers
75
views
Determining transformer equivalent circuit components
I have made a PCB based planar transformer with a turns-ratio of 8:6. I am considering the T-model as shown below:
In the T-model, Lp is the primary side leakage inductance, Ls' is the secondary side ...
0
votes
1
answer
126
views
How to stop current leaks on PC casing? [closed]
I'm experiencing an electrical current leak on my PC casing(metal). When I touch the metal parts of the case, I feel a mild shock or tingle. I'm concerned about potential safety hazards and damage to ...
0
votes
1
answer
126
views
Fixing the voltage leak on a soldering station - What should be done? [closed]
I found a soldering station Aixun T3A on youtube that got a very positive review.
The review said:
High temperature accuracy
Fast temperature heating speed
Low temperature overshoot
High power
...
0
votes
2
answers
87
views
Add Motor Speed controller to floor heating mat? [closed]
EDIT: I've updated the question. Would it be safe to add an inline PWM motor speed controller as a dimmable controller? I'm having trouble finding a floor heating mat in my country domestically. I'...
7
votes
3
answers
1k
views
Guard line preventing leakage current
I understand that we put a guard line (which is almost at the same potential as the positive voltage) to prevent leakage from positive line to negative line. Is it possible there is a leakage from the ...
0
votes
1
answer
78
views
Hipot arcing for AC and DC hipot test
I have a substrate with multiple conductor traces (0.5mm gap from each other) with aluminum plate on top used as electrode. The aluminum plate is connected to the hipot "line" and the ...
0
votes
1
answer
79
views
Right transimpedence amplifier choice for input range
I have a device that produces a ±30 nA signal and I'd like to measure this to a 0.1 nA precision.
Since the currents are so low and I don't have much time to make mistakes, I am planning to use a TIA ...
1
vote
1
answer
62
views
Unwanted PWM signal picked up in relays
Test setup: I am looking at this relay G5V-2-DC12. The test is simple. I power it up with 12V and connect a PWM signal (0V-5V 125kHz) to the common pin. I probe at the NO pin of the relay, and I ...
0
votes
2
answers
2k
views
Earth Leakage Breaker Trips .. Where is the problem?
I am trying to install a UPS in my home .. diagram of the circuit attached. UPS is in first floor. Both floors have separate main circuit breakers .. Ground floor has Earth leakage breaker while First ...
1
vote
1
answer
140
views
ATmega328P 4-button turn on, auto power off using transistor
I'm trying to create a basic 4-button battery powered remote. The logic behind it is that when one of the buttons is pushed it pulls the base of the PNP low thus turning on power to the circuit. The ...
3
votes
2
answers
2k
views
Inverter causing RCD to trip
I have an offgrid inverter/charger - an MPPSolar PIP4048MS (4000W inverter, 48V system). By and large it has worked well for 7 years.
Recently I bought an MPPSolar PIP5048MS (5000W inverter, 48V ...
2
votes
2
answers
232
views
Centre-tapped-secondary transformer's primary leakage
I hope the title is explanatory enough.
The following is the practical model of a transformer having a centre-tapped secondary (eddy and hysteresis losses, and parasitic caps are omitted):
Img src: ...