Questions tagged [monte-carlo]
For questions about Monte Carlo simulations, which perform repeated random sampling of random variables (e.g. component values subject to certain tolerances) to analyze the effects of the randomness on the overall design.
17
questions
1
vote
1
answer
49
views
How to simulate a uniform distribution around zero in LTSpice?
I am using LTSpice for a Monte-Carlo simulation, I typically use the function {mc(x,y)} for componant variability
I also want to introduce spread in the feedback ...
3
votes
1
answer
769
views
LTspice Monte Carlo Analysis Clarifications required
I am learning about LTspice MC analysis from this site. I understood almost all the things except the below one.
"Then make another spice directive to execute a Monte Carlo run as below
.step ...
0
votes
2
answers
119
views
Monte-Carlo analysis vs phase-margin or gain-margin
It's my understanding that phase and gain margins are used to see how much margin there is for the stability of a circuit. In other words, how much gain or phase would need to change in order to make ...
2
votes
0
answers
934
views
Monte Carlo Analysis in LTspice: Gaussian or Uniform distribution for the tolerance of resistors?
I am running 1000 simulations in LTspice to do Monte Carlo Analysis of the output voltage signal on a circuit with 3% tolerance resistors.
Firstly, does LTspice assume the resistors' values are ...
4
votes
3
answers
1k
views
LTSpice which values used in a run?
Running a worst case simulation, as guided here: LTspice: Worst-Case Circuit Analysis with Minimal Simulations Runs
How does one find out what circuit values were used during a run?
In my sim I have ...
0
votes
2
answers
805
views
Integrated Circuit design: Comparing the results given by corner analysis and Monte Carlo analysis
In IC design, corner analysis is performed to study the operation of the ICs under extreme conditions and Monte Carlo analysis is performed to ensure the mismatch is within the tolerance.
However, can ...
0
votes
0
answers
62
views
How to solve Laplace and Poisson's equation using Monte Carlo simulation for a parallel plate cpacitor?
I know how to solve for voltage and field using Laplace and Poisson equation for a simple parallel plate capacitor. But I cannot get any idea on how to proceed with Monte-Carlo simulation using MatLab ...
2
votes
3
answers
1k
views
Does the LT Spice monte carlo simulation definitely output the max and min voltage for any number of simulation runs?
I have the following circuit, in which i need to calculate max and min voltages possible (considering resistor tolerance).
Does running a monte carlo simulation consider the absolute max and min ...
0
votes
1
answer
239
views
LTspice Monte Carlo with different model libraries
I'm trying to figure out how to do my first Monte Carlo analysis in LTspice. I have a very simple schematic that includes the SPICE model for PN 74LVC3G17DC (vendor link).
The distribution from the ...
0
votes
3
answers
645
views
Monte Carlo Simulation In Python instead of HSPICE
Suppose I have a resistor and I want to simulate process variation on it.
When I was reading online, I noticed that Monte Carlo simulation is used for this purpose. I also noticed that HSPICE has ...
0
votes
1
answer
3k
views
How can measure the minimum value in LTspice monte carlo simulation curve?
Attached the LTspice curve result of the monte carlo simulation.
How can measure the minimum value from the curve. Here it show only the middle values while measuring. What setting change should be ...
2
votes
2
answers
2k
views
Monte carlo analysis cadence
I tried to do a monte carlo analysis of the opamp that I have designed. I ran the simulation for 100 samples with matching and process, suprisingly the results I get are very bizare. I have gains that ...
1
vote
1
answer
271
views
Virtuoso Monte Carlo Inductor Problem
For an LNA design, the simulations for the inductors and the simulation for the rest of the components (transistors, capacitors, resistors etc.) are done in two different software packages. The ...
1
vote
0
answers
325
views
PSPICE monte carlo
I am trying to do a monte carlo simulation using PPSICE(Orcade/Cadence 16.6). Most of the tutorials I see do the Monte Carlo using Orcad Capture(through the schematic approach). I would like to do all ...
6
votes
1
answer
1k
views
How much can BJT parameters (particularly beta) vary for Monte Carlo analysis
Background / Requirements:
I'm designing a typical Class AB amplifier using diode-connected BJTs to achieve the biasing. I have a requirement to keep the total quiescent current at room temperature ...