Questions tagged [differential]
Differential refers to any kind of signaling where the signal information is carried by two or more paths and both are required to properly reconstruct the signal. For example, USB D+ and D-
976
questions
0
votes
1
answer
76
views
How to calculate a differential + common mode LPF circuit?
I'm trying to validate my understanding of a differential + common mode LPF circuit using the AK4499EX datasheet (019001308-E-00 2022/07 version, p. 47). It presents the following circuit:
and its ...
1
vote
1
answer
54
views
Display port eye diagram evaluation
I was testing my display port diagram, all 4 lines.
The first three look good, the 4th line looks like it has only one signal (not differential.)
My question:
Is the 4th line okey to be like this. (...
4
votes
2
answers
1k
views
Which is preferred over differential pairs: trombones or sawtooths?
I have been told that trombones are much better to use than sawtooths, even if sawtooths may be prefered in some certians scenarios.
Here I have added trombones to the differential pairs. If I had ...
0
votes
1
answer
77
views
Distortion in a negative channel of the differential amplifier THS4505
I designed a single-ended to differential signal amplifier using a tool provided by Texas Instruments:
The source signal passes through a voltage follower (OPA810IDBVR), so the output resistance ...
1
vote
0
answers
86
views
CAN bus accidentally swapped TX and RX is it possible to solve (in firmware) without board rework
I am interfacing an isolated can transceiver with my microcontroller. My schematic is given below.
Accidently TXD is connected to RXD of microcontroller and RXD is connected to TXD of the ...
1
vote
3
answers
150
views
When compared to single-ended signals, do differential signals actually offer better EMI protection?
I'm looking for clarification on whether differential signals actually offer benefits with regards to EMI protection versus single-ended signals. Here is my current understanding (feel free to make ...
0
votes
2
answers
96
views
Differential line driver built with discrete components
I need to establish an SPI communication over one meter in a very noisy environment. To do this, I am planning on using differential communication over a twisted pair cable.
I would use a dedicated IC ...
1
vote
0
answers
26
views
What is the single line waveform of a resolver of sin or cos output?
For a resolver, the excitation signal is about 10kHz sin waveform. And the output are two pairs of differential ports: sin+/- and cos+/-.
If I test the output signal(such as sin+/-) by using a ...
3
votes
2
answers
80
views
How to obtain differential measurements with an ADC
I have a digital scope and it has also differential inputs(+in_Scope and -in_Scope). I always obtain less noisy results using them comparing to and single ended wiring. Here below I draw what I mean:
...
0
votes
1
answer
43
views
Question about differential signal routing [closed]
Would it be possible to know how we can calculate the distance that we must leave between two the two signals of a differential pair
And from what speed can we have crosstalk between the differential ...
1
vote
1
answer
80
views
Layer stack up and impedance matching- 100 ohm
I have a 14 layer stack up as follows (the stack up is from EURO circuit):
I need to provide 100 Ohm differential impedance for my LVDS on layer 7, currently by the information from the manufacturer (...
5
votes
4
answers
468
views
Ground in differential opamp situation
I have a setup like such in the provided schematic.
The idea is that I do have a -2.5 to 2.5V signal which I'd like to convert to a signal between 0 and 5V.
How should I connect my opamp? Should the ...
0
votes
0
answers
14
views
How can I analyze HighSpeed traces what on Proteus project file?
I designed a few PCB on Proteus what includes High-Speed signal traces(USB, Displayport, GigaEthernet etc.). I want to analyze that High-Speed Traces. I expect see some values like eye diagrams, ...
0
votes
0
answers
37
views
Impedance controlled PCB for USB 2.0?
We're doing a PCB for a customer that has Impedance controlled tracks for a microcontroller that seemingly might be max USB2.0, judging from lack of multiple data lines and the fact it goes in a micro-...
0
votes
1
answer
31
views
Max voltage per pin when measuring differential voltage with MCP3422
Im measuring differential voltage over a 1 Ohm (shunt) resistor at max 1 Amp, load voltage is 12V DC using one of the channels on MCP3422. MCP3422 is powered from 3v3 DC.
The datasheet https://ww1....