Questions tagged [single-ended]
An electrical signal composed of a single conductor carrying a voltage which varies with respect to a reference voltage (usually ground), as opposed to a differential signal, which consists of complementary signals carried on each conductor.
80
questions
1
vote
3
answers
175
views
When compared to single-ended signals, do differential signals actually offer better EMI protection?
I'm looking for clarification on whether differential signals actually offer benefits with regards to EMI protection versus single-ended signals. Here is my current understanding (feel free to make ...
0
votes
1
answer
141
views
Op-amp schematic connection questions and DC biasing
In the first stage the signal is converted to single-ended, and it is amplified using a digital potentiometer in the second stage to be able to change the gain with a microcontroller.
In the last ...
1
vote
1
answer
113
views
Single Ended to Differential Conversion with Opamp and Correct DC Biasing Method
First schematic below is the initial gain stage of the intermediate signal generated by mixer of radar. It is passed through sallen key high pass filter.
Second schematic for differential to single ...
0
votes
2
answers
126
views
Minimizing noise with single-ended opamps
Opamps often get used with one input at a DC voltage, usually the main ground per the standard inverting amplifier example:
For low noise, a BJT input stage like OPA1611's is often chosen for the ...
1
vote
0
answers
46
views
Mitigating 2.4GHz interference from 0-5V analog signaling line
I am chasing my tail on a project and cannot seem to find a way out of the hole.
I have a small 18mm 40kHz piezo transducer running through a powered precision rectifier+preamp circuit. This tiny ...
1
vote
0
answers
82
views
Single-ended or differential for very high frequency?
When reading the ADF4371 evb datasheet,
I realized that 16-32 GHz output uses only single-ended but all other outputs use differential output. Doesn't it mean for very high frequency the single-ended ...
3
votes
1
answer
518
views
LVDS to Singled-Ended - Transmission Line Balun Matching
I need to convert a LVDS clock into a single-ended signal. In the past I've used a voltage balun with a center tap on the secondary but I haven't found any good past 1GHz. I need to get to 2GHz in ...
1
vote
1
answer
93
views
TRS balanced audio jack insertion indicator
I'm transmitting analog audio signal from BM20 bluetooth module (it has single ended audio out L + R), to amplifier TPA3118D2.
I wish to add two TRS 1/4 balanced audio output jacks (separate for L and ...
1
vote
1
answer
213
views
Differential and single ended crosstalk and clearance
I know that there can be crosstalk between differential pairs (and you need at least a few lengths equal to the diff pair between diff pairs, usually 3 or more diff pair widths).
What is the ...
0
votes
0
answers
158
views
DC-coupled wide-bandwidth differential to single-ended conversion
I'm designing a circuit that produces differential signal outputs in the frequency range from DC to about 2 GHz. This differential signal will be driven by an FDA (probably LMH6401 or LMH5401). I'd ...
1
vote
1
answer
90
views
Differential voltage to frequency
Edited to clarify some questions
I’m working on a design that will take a 0.5V-4V signal from a laser displacement sensor (Keyence Il-1000) and convert it to a frequency signal (0.1-2Mhz) for input to ...
0
votes
2
answers
963
views
Single-ended digital signal to RS422 differential signal
I'm trying to control a laser scanner from an Arduino board. The Arduino outputs a single-ended digital signal 0V or 3.3V. The signal I'm transmitting to the laser is the same signal as I use to ...
6
votes
8
answers
2k
views
How does the current of RS485 signals return from the receiver to the sender?
I am planning a system consisting of 1 master device which is connected to 19 slave devices using RS485 transceivers. Also, all devices are powered by 1 PSU. A simplified schematic is shown below.
As ...
0
votes
1
answer
120
views
MAX1032 ADC Single-Ended reading/conversion problem
I want to use the MAX1032 ADC (datasheet) to measure a voltage (Vin) through a voltage divider (30K/3K) with a PIC microcontroller over SPI. I have written a simple library for Single-Ended Unipolar ...
4
votes
2
answers
272
views
Single Ended Signal Ground In a Loop
I have ten devices that I need to connect in a loop so they can send data from one device to the next until it returns to the original device. The devices are about 5 inches apart.
They are all 5V ...