All Questions
Tagged with buck power-supply
224
questions
0
votes
0
answers
17
views
Buck Average Modelling
I completed average modelling with Voreperian PWM switch model as described in Christophe Basso's book "Transfer Function of Switching Converters" and I compared the average model with ...
0
votes
1
answer
98
views
Buck Converter Peak Current Mode Control Average Model
I am trying to understand average model of Buck Converter for Peak Current Mode Control Topology.
Below snapshot taken from Christophe Basso Webpage(https://powersimtof.com/Spice.htm) from file "...
0
votes
0
answers
23
views
Does a buck-boost converter serve as enough circuit protection for an automotive application? [duplicate]
I am designing a circuit for a automotive application which is meant to map voltage ranges between two airflow sensors (i.e. 1 sensor has an output range of 1.75-7.0V and I want to replace it with a ...
2
votes
1
answer
77
views
Peak current mode control loop compensation calculations
I recently came across a rather nice straight-to-the-point application note by RickTek (AN028) on how to calculate approximately the compensation network of a PCM buck regulator.
Link : https://www....
4
votes
4
answers
565
views
Inductor energy storing in buck converter
I am trying to understand inductor energy storing during ON time in buck converter.
Energy stored in inductor of buck converter is (Input Power -Output Power)*Ton
Lets say output power is 5 W and ...
0
votes
1
answer
165
views
Audible Noise in MC34063-Based Buck/Boost Converter Circuit
I am trying to make a hotplate with an ESP32 and I use MC34063 for buck/boost converters. The hotplate itself require 12-30V to operate and the ESP32 and LEDs need 3.3V.
Here is the circuit:
When the ...
0
votes
0
answers
35
views
Debugging buck converter IC having trouble reaching stable power good after short
I have a 5V power supply circuit from coming from a 12V in to 5V out of a TPS54620 on an FPGA development board I purchased. There was an incident with a bad header connection that caused a GPIO pin ...
0
votes
1
answer
108
views
Should I put my buck-converters in parallel or series?
I'm supposed to have two voltages coming out of two buck converters. My starting voltage is 12 V while the buck converters are supposed to output 5 V and 3.3 V respectfully.
Should I make the output ...
0
votes
1
answer
68
views
Schematic review MAX20029ATIAV
I am using a MAX20029ATIAV in my design for powering a Quad Tunneling GMSL2/1 to CSI-2 Deserializer.
MAX20029ATIAV is Quad Low-Voltage Step-Down DC-DC Converters.
My schematic is given below. May I ...
0
votes
0
answers
60
views
Best power supply configuration
I'm making a power supply board with a buck converter for a 2A maximum and I would to know which is the best configuration between these two:
Is it best to put the input filter, a parallel damped LC ...
1
vote
1
answer
89
views
Custom buck converter putting out 1V instead of 5V
I "designed" a simple buck converter, which is basically a clone of the 5V reference design in the TPS6293x datasheet. Unfortunately, my converter is only putting about 1V (closer to 0.95V). ...
0
votes
1
answer
78
views
Circuit to convert 14.8v battery with max 4a discharge current into 12v, 9v and 5v output?
I am making a robot with multiple devices mounted on top. I am planning to buy either a 14.8v or 11.1v Li-ion battery which has internal BMS limiting maximum discharge current to 4A. Now I need 9v for ...
0
votes
0
answers
20
views
Deriving Power Budget for SAMA5D27C from Datasheet
I am spec'ing out my power distribution network and trying to figure out what Buck converters I am going to need for a Microchip MPU design using SAMA5D27C. I am looking through the data sheet below ...
1
vote
1
answer
125
views
Burning sound from the PSU
I am trying to make a bench power supply from an old 350W PC PSU
that provides 4 lines
3.3V 8A
5V 9A
12V 11A
-12V 1.5A
Here is the connections diagram:
I used this step down module to be able the ...
0
votes
1
answer
130
views
Buck converter not behaving as anticipated with new trim pot resistors
I recently purchased a 300W buck converter from amazon 1 which has two 3296W 100K trim pots to control the constant current and constant voltage output. My plan was to use them as bench power supply ...