Skip to main content

Questions tagged [smoothing-capacitor]

The tag has no usage guidance.

0 votes
0 answers
68 views

How can I smooth the output of a DC motor used as a generator?

I have a small DC motor acting as a generator, spinning at 500RPM. From it, I get 1V with ½V ripple, which a 1000uF electrolytic capacitor smooths nicely. I may wish to drive the motor in reverse, ...
GrahamRounce 's user avatar
2 votes
2 answers
1k views

Function of capacitor on the output of a bridge rectifier

What is the function of capacitor C in this diagram?
Kim Sr Luy's user avatar
5 votes
3 answers
570 views

How Can Non-Parasitic Capacitance Be Excessive When Smoothing Voltage?

I mostly do VHDL/Verilog, and I'm laying out a PCB for a small FPGA project. The FPGA will operate in a noisy environment. I want to make sure the board has more than enough capacitors to provide the ...
James Strieter's user avatar
1 vote
1 answer
120 views

Why does the capacitor discharge after the peak of AC voltage (smoothing)?

Why does the capacitor discharge (used as a battery to provide voltage to the resistor) after the peak of the alternating voltage (after the voltage reaches the highest value and goes on to decrease ...
Crown Raven's user avatar
0 votes
3 answers
1k views

AC to DC rectifier and smoothing

I'm trying to understand how you get a DC signal from an AC signal being rectified. It produces a ripple waveform and the signal gets "smoothed" out using a smoothing capacitor. Is the ...
Amadeus 's user avatar
0 votes
1 answer
854 views

Using RC Low Pass Filter for PWM signal Smoothing [closed]

I have some questions regarding the working of RC Low pass filters, specifically for smoothing out high frequency PWM signals (application: making a buck converter for driving an LED (expected current ...
Maarten -Monica for president's user avatar
0 votes
3 answers
167 views

LED blinker draws high current during switching, how to prevent current spikes

I have the circuit below: Now focus your attention on TP4056 charging and protection module because it has a DW01A battery protection circuit in it which detects over current at 3A. Also focus your ...
CaveScientist's user avatar
0 votes
2 answers
261 views

Behaviour of parallel RC circuit attached to 'rectified' DC and AC voltage source

I have been having some trouble understanding the functioning of a capacitor and a resister attached in parallel to a rectifier to smooth out the time-variant dc output. From what I have read, a ...
watch's user avatar
  • 1
0 votes
1 answer
384 views

PWM average voltage smoothing

I built an ESC circuit. First, I tested it with a drive frequency of 350 Hz; the speed was at about 20 RPS at a 70% duty cycle. But when I changed the drive frequency to 20 kHz, I noticed that the ...
0ussama's user avatar
  • 121
0 votes
3 answers
200 views

Schematic notes: Place capacitor as "close" to pins: Is this a necessary note? Is it a significant point?

Background I am building a ATMega4809 board that allows the board to be programmed using the Arduino IDE. While examining the following schematic I noticed that where the caps are placed the author ...
raddevus's user avatar
  • 1,272
9 votes
5 answers
3k views

Why does a 2nd capacitor and coil smooth this signal?

I came, more or less accidentally, across this image here: I understand all circuits and their resulting signal output, except for the last/lowest one. Shouldn't it look like this with one capacitor ...
Ben's user avatar
  • 625
1 vote
1 answer
330 views

Capacitor across motor vs capacitor across motor and transistor

I am currently building my own control board for a high power brushed DC motor (24V 16A). I am using an Arduino to provide a PWM signal to an IRLB8743 MOSFET. The reason I am trying to build my own is ...
Quadracycle4000's user avatar
3 votes
3 answers
2k views

Which capacitors to use with voltage regulator IC such as 7805?

Many of the tutorials suggest to use a large smoothing capacitor (tens and even hundreds of uF) with a full wave rectifier but the datasheets of the voltage regulators and some tutorials suggest only ...
Asmat Ali's user avatar
  • 333
0 votes
1 answer
526 views

Which is better for full bridge rectifier circuit? MLCC or Electrolytic? [duplicate]

If I place 100uF multilayer ceramic capacitors at the output of a full-bridge rectifier will there be any problem? Or I need to place electrolytic capacitors? What difference do they make (except size)...
Sadat Rafi's user avatar
  • 2,521
0 votes
1 answer
267 views

diode required for smoothing capacitor

I never quite understood the finer details of why a diode is required for turning capacitors into "smoothing" capacitors instead of just low pass filters. The simulations I have done in ...
attle's user avatar
  • 49

15 30 50 per page