Questions tagged [ac-dc]
Questions regarding the safe and effecient design and implementation of AC voltage to DC voltage supplies. Typically Mains to some lower DC voltage.
441
questions
0
votes
0
answers
35
views
Ground connection of power converter and MCU
I've designed an AC/DC power converter PCB, with input, and output voltage sensing, but I have problem connecting it to microcontroller board, i'm using F28379D launchpad as the microcontroller.
I ...
- 11
0
votes
0
answers
20
views
How should I come up with a power supply for 5 motors, one micro-controller (ESP32) and one microprocessor (Jetson Nano) for an object sorting arm
I am trying to design a power supply for a robotic arm with 5 servo motors(2 are MG90S and 3 1501MG motors). I'm planning to use an ESP32 microcontroller and Jetson Nano.
I have the option of using ...
12
votes
6
answers
3k
views
Second opinion on PCB design for relay made in Altium
Edit: I have added the updated PCB design at the bottom over this post (for anyone curious about the progress)
And a big thanks to everyone who commented, it really helped me out a lot!
Original ...
- 135
0
votes
0
answers
50
views
Verify the correctness of a circuit: AC to DC conversion for Arduino Nano and relays
I need your opinion about the correctness of my circuit. As is shown in the drawing schematic, the circuit is supplied by 220 VAC which will be converted to 12 VDC. This output is used to supply the ...
- 1
0
votes
1
answer
51
views
LTspice AC/DC converter with DC/DC boost converter
So this is my first time using LTspice and I need to convert my (AC) Vin 11.5V to DC and then boost DC voltage to Vout 22.5V. I have a few givens and some I needed to calculate. I am struggling to ...
0
votes
1
answer
57
views
DC-DC design with STUSB4761
I am designing a powered USB HUB (UFP) which can provide power to the host through USB PD. This means I need a PD controller which supports DR_Swap and it seems that STUSB4700/STUSB4710 cannot be used ...
- 3
0
votes
0
answers
29
views
Understand firing angle chart in dual converter
How to understand below Firing Angle Chart,
I guess the y axis should be voltage of the source, but what is the x axis, why a1/a2 points right, the location of 0⁰/90⁰/180⁰ seems quite strange.
Hints ...
- 95
2
votes
5
answers
175
views
How can an AC adapter push 11A but only suck 2A?
I have a laptop adapter that takes in 120V AC and converts it to 20V DC. The adapter is rated for 230W (11.5A 20V.) Knowing conservation of energy and such, this means that the adapter takes in 120V ...
- 145
0
votes
1
answer
71
views
Calculating input power of ACDC power supply
I'm trying to calculate the input power draw of an ACDC power supply that we are using in a control chassis and am confused by what to me looks like conflicting information in the datasheet.
The power ...
- 156
1
vote
1
answer
63
views
Ground connections around bridge rectifier in flyback converter
I am designing a flyback converter and I am being told to make the ground net connections as shown in the image below.
I think this is colossally dumb because it eliminates PRI and SEC isolation. I ...
user224284
1
vote
0
answers
58
views
esp32 s2 touch sensor read
I have a problem with capacitive sensor. I have created PCB with 2 capacitive sensors. Everything is working fine and ESP32 s2 mini reading values as I expect while I powering up esp32 with type-c 5v, ...
0
votes
1
answer
58
views
Seeking a good solution for mitigating the effects of high in-rush current caused by an AC-DC converter [closed]
Many AC-DC power supplies (say, 220VAC to 24VDC) have huge inrush current values. For example, a device might have an inrush current of 80A@230VAC. This raises the question of how to handle the ...
- 474
0
votes
2
answers
73
views
NiMH battery charging problem
I have a battery (8 cells in series, NiMH AA cells (1.2 V to 1.3 V), 1300 mAh per cell).
Cells used-
https://www.amazon.in/Rechargeable-NiMH-2300-Peak-Power/dp/B01MF8HUKO
https://www.amazon.in/...
0
votes
2
answers
142
views
Is there a 3-phase to DC converter that draws current proportional to voltage?
Of course, 3-phase alternating current can be converted into a rippling direct current with a 3-phase bridge rectifier.
This design only draws current from the two phases with the most voltage ...
- 443
0
votes
2
answers
76
views
What AC/DC adapter do I need to power 10 high-power (3W) LEDs?
I'm attempting to build a near-infrared (850 nm) lamp using high-power LEDs and am struggling to design a suitable way to power them directly from the AC power plug (220V).
I have 10 high-power LEDs ...
- 1