Questions tagged [dovetail]
Dovetail joinery, tools techniques to create them.
19
questions
1
vote
0
answers
85
views
Sliding dovetail expansion
I am making a bookshelf. There are going to be 3 fixed shelves attached with sliding dovetails. The top shelf is 1/4 inch from the top of the side. The bottom and middle shelves went in fine, but the ...
- 123
2
votes
3
answers
661
views
Dovetails with undermount drawer slides
To practice my dovetails, I decided to make some drawers for my kitchen cabinets. I'm using Blum undermount slides, which requires the drawer to conform to specific specifications, as well as a few ...
- 123
0
votes
2
answers
702
views
What is the best way to cut a dovetail on the end grain
I am making a medicine cabinet and I want to use a stopped, sliding dovetail joint so that the joint will be hidden. I can cut the sliding dovetail in the side boards with a dovetail bit in a router, ...
- 121
2
votes
0
answers
134
views
Would a dovetail key(s) in a beveled (mitered) chest panel be adequate strength for a larger box?
I'm building a hope chest for my daughter out of cherry, and wanted to use dovetails to join the panels. My hand-cutting skills aren't quite up to snuff for a fine detail like through dovetails, so I'...
- 21
4
votes
1
answer
574
views
pine panels with minor cupping suitable for dovetails?
I have these 9”-wide, 3/4”-thick pine panels from the bigbox store that i would like to make into a carcass with dovetails.
Such panels commonly exhibit some cupping, but have some spring into them, ...
- 1,647
4
votes
1
answer
186
views
Dovetailed spine?
I snagged the image below while looking online for dovetail examples.
Instead of two boards coming together, it appears that the joint, what I called the spine in the title, is a third piece to ...
- 243
10
votes
2
answers
3k
views
How does Frank Klausz achieve a >90 turn with a turning saw without cleanup when cutting dovetails?
Frank Klausz, in his video titled "Dovetails for Drawers - The European way" takes two minutes to show how he makes his "3-minute dovetails". When cutting the tails, he uses what looks to be a custom ...
- 1,647
6
votes
3
answers
1k
views
How to hide base dados behind box joint corners
I don’t have any photos on me so hopefully I can describe this ok. Say I build a box like so:
Cut the four sides.
Cut dado in bottom of each side, on table saw (I don’t have another good way), which ...
- 5,613
1
vote
1
answer
1k
views
Styling dovetail box - tails or pins on front side
I am building a box to hold some of my router bits and will use dovetail joints for the vertical sides. I am not sure what to put in front, the tails or the pins.
Aside from mechanical considerations,...
- 1,135
4
votes
2
answers
190
views
How thin can a large dovetail tail be?
I'm building a small (12"D x 24"W) workbench for doing woodwork in my apartment. I want to dovetail the legs to the top, but the tail on the end will be about 1/2" wide on the narrower end. Is this ...
- 143
3
votes
1
answer
969
views
Safe thickness for sliding dovetail in shelf
I am at the last cuts for a shelf which my wife asked for.
The whole thing is made out of cherry. The shelf top is 7/8 inch thick.
The supporting brackets which are mounted to the wall studs are ...
- 970
1
vote
1
answer
355
views
Simple Dovetail jig
There is a small dovetail jig my teacher has that he showed the class and I thought it was neat and want to make it. Here is the video I think he got it from. Because it is very much the same thing, ...
- 3,116
3
votes
2
answers
325
views
Adding weight to Veritas dovetail saw
I am trying to learn dovetails. My first/second/third show slow improvement but I still have a lot of progress left. The most difficult part for me is starting the cut since the saw tends to want to ...
- 970
8
votes
2
answers
260
views
How to get better at fitting joints and "seeing" bruises?
I'm a beginner. I'm concentrating on hand-tool joinery for now. I've watched a lot of YouTube videos, trying to learn joinery. For the purposes of this question I'm most interested in mortice &...
- 584
3
votes
4
answers
3k
views
How do I stop tearout when using a dovetail jig
I am using the Rockler dovetail jig on some 3/4" walnut. I have been successful one time with this jig but I always manage to have issues cutting the tails. I am using the bits that come with the jig ...
- 153