Questions tagged [dado]
The dado tag has no usage guidance.
27
questions
1
vote
1
answer
54
views
Enclosing an MDF sheet in 4x4 Cedar
I am building a headboard for a bed, and want to put an MDF sheet inside a dado in 4x4 cedar boards, as shown in the image:
Should I make the MDF free floating in case it swells? Or glue it to the ...
3
votes
2
answers
6k
views
What size dado set to use for 10" table saw?
I'm a noob with a new table saw and confused about buying a dado set for it. It is a 10" saw with a 5/8" arbor -- a Laguna Fusion 2. But I am finding zero dado options on the market for this ...
1
vote
1
answer
231
views
Not aligned Dado shelves - does it need correction? (With pictures)
I was trying to make some dados for a shelf for the first time and unfortunately, they did not come out perfect. The dados on the left and right side are unaligned, about 0.5-1.5mm (~1/32").
The ...
0
votes
1
answer
330
views
Tablesaw dados on long boards with kerfmaker
Hardware used: tablesaw with flat kerf blade, kerfmaker, tablesaw sled.
Premise: I've made a kerfmaker and have been very pleased with it in making dados on short boards. However, I' m at a loss on ...
0
votes
0
answers
262
views
Building a rectangular pyramid
I have made a set of Yahtzee™ dice from a 4x4 post. We have been using a bucket as the 'shaker cup'. I would like to construct a wooden 'cup'.
My concept is two use two identical rectangular pyramids, ...
5
votes
2
answers
2k
views
Is it safe to use just the chippers in a dado stack?
I have a dado set that comes with a 1/16" and a 3/32" chipper. These will be perfect for the 5/32" dado I need to cut. Unfortunately, the outer blades are each 1/4", so there's no ...
1
vote
1
answer
282
views
Leaving floating space for a panel - do I need to center the panel?
If I cut a dado 2mm (1/16"+) bigger than a panel leaving space for movement, do I also need to leave 1mm of space on each side of the panel when inserting it or will the panel adjust itself?
This ...
1
vote
2
answers
4k
views
Using a 5/8 dado stack on a "30mm" arbor
Background
I would like to buy a dado stack, but 30mm is hard to come buy due to laws forbidding selling them in Europe. Using them for personal use is ok, so I can order from abroad.
Question
I have ...
3
votes
2
answers
3k
views
Nails plus glue into endgrain vs screws plus glue vs dado (for shelf)
I'm building a hutch/book shelf for a small desk (2'x4'). Width of hutch is 48", depth 9.25", height about 18". Wood is nominal 1" thick "appearance boards" from a big ...
4
votes
2
answers
2k
views
Cutting rabbets against the fence with a table saw
I'm very new to woodworking (I've only just started out in an online course), and I've been trying my best to educate myself on safe practices. Recently, I've been thinking about how rabbets are cut ...
6
votes
3
answers
1k
views
How to hide base dados behind box joint corners
I don’t have any photos on me so hopefully I can describe this ok. Say I build a box like so:
Cut the four sides.
Cut dado in bottom of each side, on table saw (I don’t have another good way), which ...
1
vote
1
answer
399
views
Can I avoid spur / knicker marks in dado bottom cut with plough plane (stanley #45)?
I want to use a plough plane (stanley #45) to cut dadoes (cross grain). The spurs/knickers are useful in preventing tearout and defining a clean knife wall, but they score past the bottom of the dado, ...
3
votes
2
answers
3k
views
How to Cut Dados in MDF with Hand Tools
I’m new to woodworking and was wondering about the best way to cut dados in MDF. I’ve seen tutorials on cutting dados in real wood using chisels, but I don’t know if it applies to MDF as well because ...
1
vote
2
answers
573
views
Compensating Rabbet or dado in warped plywood
I'm building some 3x3x16" long L brackets out of 3/4" plywood. I'm planning on using a simple butt joint with a single rabbet and screws to attach the two pieces together.
The strips are all bowed/...
2
votes
1
answer
2k
views
What depth and offset from edge my dado / groove in particle board should be?
This is a follow-up on this question (How to make bottom for a big drawer)?
I have also read this one (What are the minimum, maximum, and optimal depths for dadoes, grooves, and rabbets) and I'm not ...