Questions tagged [drawer]
The drawer tag has no usage guidance.
26
questions
2
votes
1
answer
48
views
Making a thick door not catch on a drawer front
I am planning a sideboard that has 2 sets of doors on the outside and a pair of drawers in the middle. The desired appearance of the doors and fronts requires that the doors be as thick as 1.5 inches. ...
- 21
0
votes
2
answers
73
views
Alternative drawer joints
I am planning to replace two cupboard units of my old IKEA kitchen with one unit with three drawers. I have most of the parts planned, except for the attachment of the drawer fronts.
On the existing ...
- 153
1
vote
1
answer
865
views
Thin wood (~12mm) for drawer boxes
I'm replacing some drawers I've had for a while that were built with the Hafele metal side and slider system.
I will be making these new drawers with wood as I'm upgrading the slides to full ...
- 441
2
votes
2
answers
53
views
Drawer face replacement help
My kitchen is missing a drawer. I have rebuilt the box but need help finding or creating a replacement drawer face.
I have looked at hardware stores and they don't seem to have the correct style.
Is ...
- 121
9
votes
2
answers
2k
views
Why an extra drawer face?
I am new to this site and I am neither a woodworker nor a carpenter. I’m sorry if this question sounds naive.
I watched many YouTube videos about constructing drawers. Unusually it has 4 sides joined ...
- 193
0
votes
2
answers
80
views
Kitchen/Workshop unit design
I'm wanting to add some storage and organisation to my workshop shed and my initial idea was to basically build some frameless kitchen units.
My depth will be 400mm and my total available length is 2m....
- 441
4
votes
1
answer
1k
views
How to determine drawer weight capacity?
I am fitting my pantry with custom drawers, and I am worrying a bit about the weight capacity of one drawer in particular. The drawers are 14" wide and 21" deep. I've constructed them with ...
- 145
4
votes
1
answer
757
views
How do I use the oval screw holes in drawer sliders?
I am beginner/intermediate in woodworking and I am busy replacing my drawer sliders and hinges in my kitchen cupboards.
I have noticed that the hardware I'm using has got oval screw holes in addition ...
- 151
3
votes
1
answer
595
views
Drawer slides sticky with new drawer, common causes?
I am modifying a standalone cabinet to have a single, large drawer for holding garbage/recycling etc.
So far so good, however, when sliding the drawer in, the last 3-4 inches are pretty stiff/sticky. ...
- 975
0
votes
0
answers
210
views
Correctly spacing drawer runners (with soft close mechanism)
I have a cabinet carcass that I am wanting to fit drawers in, however I'm a little unsure about it and seeking some advice.
My carcass is 710mm tall with 18mm base and spacer, so the height for drawer ...
- 441
1
vote
0
answers
123
views
How difficult is it to go from Blum Tandem Plus to the Blum Legrabox drawer system for a DIY cabinet maker [closed]
I built a couple dozen Blum "Tandem Plus" kitchen drawers many years ago (3/4" prefinished maple), with the grey metal sides and they were relatively easy to build and install.
Now it's ...
- 103
0
votes
1
answer
643
views
Reinforce glued butt joints?
I'm an absolute noob when it comes to woodworking, but now I'm in the middle of my first (some sort of) drawer/shelves building project.
I've glued together all four sides (store bought edge glued ...
3
votes
1
answer
395
views
Will forcing a twisted drawer front flat cause issues?
I'm working on cherry drawer fronts for a dresser with inset drawers. The drawer in question is 38" wide and about 8" tall. The drawer itself is 1/2 Baltic Birch.
The board has already been ...
- 132
1
vote
1
answer
170
views
Removal of swan neck drawer handles
I'm restoring a pine table. The two drawers have old drop down swan neck handles which I want to remove in order to properly sand and then varnish the drawers. I've taken the bolts off the two screws ...
- 11
1
vote
1
answer
171
views
How tall can a drawer front be?
I would like to build a drawer similar to the picture below. I already have a panel-style door which is ~ 560 x 780mm with solid 20mm maple as stiles and rails.
I will be pulling this drawer ~ 20 ...
- 133