Questions tagged [load]
An electrical load is an electrical component or portion of a circuit that consumes electric power. This is opposed to a power source, such as a battery or generator, which produces power.
578
questions
1
vote
1
answer
62
views
Identify SOT23-6 smd marking code 169 324
This chip in electronic load DL24M, please help me identify it.
pin 4 it's out
and connected with pin 1 LM321 (on 4pcs lm321)
- 13
-1
votes
1
answer
47
views
Can you help me understand W=I*V - house load
So I'm trying to work out my daily Ah usage for an off-grid set up (and to see what my power bill at this new place might be like).
Context:
I've gone through and created a sheet with the appliances I ...
- 99
0
votes
1
answer
14
views
Managing Solar Power, battery, and load for raspbery pi - designing power management system
So, I am working on a scientific instrument that measures air quality. It uses a raspberry pi with a couple of sensors. Essentially, this instrument is going to be deployed in an Urban area in a ...
- 1
0
votes
1
answer
54
views
Grounding PV solar, battery and load
I have simple diy solution for solar system. The system is build using esp32, 2x ina266, ads1115 and acs758. The esp is powered from usb 5v (stepdown from battery) and 3v3 is then distributed into all ...
4
votes
2
answers
220
views
50 ohm vs HiZ setting on function generator?
I got my first function generator today. The generator is a SDG1032X.
It gives you the option to switch between 50 Ω output and HiZ (high impedance) output by long pressing the output buttons.
It does ...
- 51
1
vote
0
answers
48
views
Low-Side Driver Not Sourcing Current from Load to GND
I have a circuit with an electronic load in parallel with an optocoupler and a low-side N-channel MOSFET connected to the circuit. The low-side N-channel MOSFET driver is supposed to source current ...
- 11
0
votes
2
answers
60
views
Load sharing effect on heat dissipation [closed]
In a circuit, when two ideal components are used in parallel instead of using just one (same component in both cases), does it have any effect on any of the temperature values? junction / case / ...
- 1,061
1
vote
1
answer
69
views
Why do the number of valleys change when load is changed? [closed]
I am operating a flyback converter with 60V DC input and 6V DC output. The load connected across the output is 500mA. My mode of operation is DCM. If I have 4 valleys in the magnetizing ringing of Vds ...
- 33
-1
votes
1
answer
78
views
How does an AC of 5100W (1.5 ton) capacity work without any issue with 1000W of total electricity load of my house? [closed]
I have one AC of 5100W (1.5 ton) capacity and I generally run it along with other appliances like fans, LED bulbs, TV and more. My house is sanctioned ...
- 139
0
votes
0
answers
18
views
Voltage drop of each load in the radial network
How do you find the voltage drop and external loop impedance of each lighting load in the picture attached?
0
votes
1
answer
38
views
Controlling On/off of WL-134 Module with ESP32
I want to control on/off of WL-134 RFID module from GPIO of ESP32. WL-134 requires 9V, 140mA on its input so Basically I want to control 9V input from GPIO of ESP32 when I dont want to use RFID module....
0
votes
1
answer
86
views
Driving a power MOSFET successfully
I have recently purchased this power MOSFET for a project (dump load resistor):
https://uk.rs-online.com/web/p/mosfets/6867852?gb=s
Alongside this I have bought a MOSFET driver see link:
https://uk.rs-...
- 49
3
votes
1
answer
76
views
Voltage drop issues in LTspice simulation for buck converter using SW model
I have a LTspice design issue where I encounter the same problem, even when I use other available simulations.
Whenever I increase the load, there is a significant drop in voltage, despite having ...
- 524
0
votes
1
answer
44
views
Diodes selection for High Side switch protection against inductive load
Hello I would like to design protection for HSD, BTS7200-2EPA against inductive load. Spec data for the inductive load is limited. But the PCB was designed for 2.5A peak, and approximate L and R_L ...
- 1
1
vote
1
answer
72
views
How much current can I pull out of a battery
So I know an average PP3 9-volt battery has about 500mAh of capacity. If I wanted to, for example, draw 3.5 amps, the battery would last about 8 or 9 minutes, though that would be assuming the battery ...
- 173