All Questions
Tagged with load resistance
23
questions
0
votes
1
answer
200
views
How higher load (high R) draws more current when the nature of resistance is to reduce/restrict the current?
Consider a voltage in a circuit(say 100 V) in a closed circuit, and a resistor 10 ohm and a Load of 20 ohm connected across it.
when you turn on the switch, current through them is almost 100/30 (3.33~...
0
votes
2
answers
154
views
Voltage fluctuations in TIP122
I have used the following circuit diagram for power supply using a transformer,simple bridge rectifier and filter capacitor at the back of it to get 12V dcI have used the TIP122 as shown:
Idealy the ...
0
votes
1
answer
375
views
How does capacitive loading and inductive loading differ from resistive load?
A voltage source is loaded when current is drawn from it. Usually we have voltage sources in circuits and not current sources. A resistive load draws current from a voltage source that is a function ...
-4
votes
4
answers
205
views
Power supply for remote load
I tried to design power supply circuit myself because no power supply would do for me (or I'm just unaware). My issue is that I have power supply far away from load and there is no way I can shorten ...
0
votes
0
answers
34
views
Implementation of a 24 hour variable resistive load fluctuation
I am implementing a DC microgrid with a variable resistive load variation of 24-hours, based on a load profile.
I have implemented it in MATLAB through a variable resistor and a 1-D block to provide ...
1
vote
0
answers
75
views
Can I connect low-power resistors to achieve a high-power resistive load?
I've designed an 80 W 400 V PFC boost converter and I want to test it with resistive load. but I couldn't find a low-cost high power (20 to 80 watts) resistor in the range of 2k to 10k ohm. Is there ...
1
vote
3
answers
298
views
Load impedance seen by op-amp
I have a question about the load impedance seen by an ideal op-amp output terminal in inverting configuration.
When calculating the load impedance, we set Vin = 0;
In one way I could say that the ...
0
votes
1
answer
93
views
Usually Geiger tubes have a recommended 1 to 5 megaohm anode load. What determines that value and what is the effect of increasing the value?
I think title is sufficient. Changes? Dead time, signal out amplitude, plateau character, etc.
3
votes
5
answers
3k
views
What load resistance will result in maximum power transfer - Art of Electronics
I am reading Art of Electronics book. There is a question:
Here is an interesting problem: What load resistance will result in maximum power being transfered to the load for a given source resistance?...
0
votes
3
answers
207
views
Is there a way to somehow "isolate" a voltage drop?
I have a small issue with voltage drop. I'm working on a project, where I have five resistive wires (approx. 8 ohms each) connected to li-ion battery pack in parallel. The battery pack outputs 16.8V ...
1
vote
1
answer
1k
views
Gain with load or gain without load?
There is a problem I have been dealing with for hours.
In my Electronic 1 lecture, small signal analysis was like this:
The small signal equivalent of this circuit in my lecture notes was this:
When ...
0
votes
1
answer
2k
views
How do I calculate load resistance?
I'm here with yet another problem. This time I can't figure out what the question wants. I've calculated the Thévenin equivalent, however I can't work out how I should calculate the RL.
Is the load ...
-1
votes
1
answer
118
views
Which load resistance is connected to generator U2?
I have this op amp and one of the questions says
Which load resistance is connected to generator U2?
This is my attempt but I can not confirm if it right.
No it's not homework, it examples I'm ...
0
votes
0
answers
156
views
Difference between horn and power resistor?
I have a circuit where my microcontroller is turning off and on a heavy load using a power MOSFET (I've also tried it with a MOSFET and a relay which yielded the same results). When I use a power ...
0
votes
1
answer
65
views
Ohm's Law in Practise
When the AUX pin of a stereo is connected to my mobile phone's audio female port, I just measured the voltage at the end of this AUX pin(No load is connected) approximately 2mV using a DMM . But when ...