Questions tagged [electrolytic-capacitor]
An energy-dense polarized capacitor type, used in low-frequency filtering applications.
374
questions
1
vote
4
answers
2k
views
Can I substitute a capacitor with the same rated capacity and voltage but a lower inductance and higher rated ripple current for a mobo repair?
I have an early to mid 2000's motherboard that I am trying to restore. It looks to be mostly in good condition but a blown radial electrolytic capacitor might be causing trouble. From the placement of ...
0
votes
0
answers
172
views
Powering RTC DS3231 through BAT pin while keeping the coin cell battery in place
I'm working on a battery-powered DSLR camera controller with a MCU (ATMEGA328P) that spends most of the time in deep sleep and a RTC (DS3231) that wakes up the MCU a few times a day to take a picture. ...
2
votes
3
answers
573
views
Formula for calculating capacitor balance resistor values
The following formula is generally used for calculating balance resistor values used for overvoltage protection of capacitors in series when the individual capacitor voltage ratings are below the ...
5
votes
2
answers
805
views
Voltage drop due to leakage current in capacitors in series
When capacitors are connected in series in a DC circuit, the voltage drop across individual capacitors at and immediately after the initial charging period is inversely proportional to the individual ...
4
votes
2
answers
297
views
How to remove a capacitor or resistor from an electronic circuit
I would like to modify my amplifier (Peavey 6505+ 112: https://www.thetubestore.com/lib/thetubestore/schematics/Peavey/Peavey-6505PLUS-112-Schematic.pdf), by removing some components and testing some ...
0
votes
1
answer
254
views
Two modes of electrostatic force with charged capacitors?
During a charged state of a capacitor (Regardless of the type of capacitor),
Simple parallel plate:
.png
Parallel plate with dielectric material in the gap:
]3
Supercapacitor:
How is the ...
0
votes
2
answers
279
views
Found some SMD capacitor leakage, can I sand them to clean the PCB?
After removing the 3 electrolytic smd capacitors from a car ECU, I found some leakage, although not sure if this is the main culprit of the problem in my ECU, but I'd like to clean them. I tried 99% ...
1
vote
1
answer
403
views
Identifying a vintage capacitor
This is inside an Allen Wales (Model 9E) adding machine. It was manufactured in the late 30s or maybe sometime in the 40s from what I've read. There are notes from a technician scratched on the inside ...
0
votes
1
answer
73
views
Capacitor mounting in switched power supply
I'm repairing switched power supply. It is custom inside device and cannot be changed with another power supply. It is not first time I've had to repair it. The problem is always the same: grilled ...
4
votes
2
answers
1k
views
Footprint for Electrolytic Capacitor
I plan on using this capacitor on my project:
https://datasheet.lcsc.com/lcsc/2209011730_KNSCHA-RVT330UF50V167RV085_C5155333.pdf
This is an electrolytic capacitor (this means it has polarity.).
The ...
0
votes
1
answer
103
views
What is the effect of the dc link capacitor "rated ripple current" on the drain current of switching elements?
While using a capacitor with 2.3A rated ripple current as a dc link capacitor in the circuit (as shown in the picture below "Cd") I used, I replaced it with one with 2.8A rated ripple ...
0
votes
1
answer
89
views
Calculate needed capacitance
I have this application which requires 18VDC as well as 12VDC. To get 12V I have designed a buck converter circuit which can supply up to 2A.
The problem:
The 18VDC (3.33A) supply may suffer from ...
5
votes
3
answers
16k
views
Why, when calculating rise time, do we use 2.2·τ? (RC low-pass circuit)
I am just trying to understand why we use 2.2·τ when calculate the rise time. I can't find a derivation anywhere, I don't understand where this 2.2 comes from.
4
votes
2
answers
2k
views
How is bulk capacitance for a brushed DC motor H-Bridge calculated in the real world?
There's a lot of great information on driving DC brushed motors from h-bridges. Preventing back-emf with diodes and bulk capacitance from electrolytic capacitors
When designing a high powered h bridge ...
3
votes
3
answers
295
views
Should I measure ripple current on a replacement capacitor of lowered ESR?
I've changed an 820 μF capacitor on the output of a 1.05 V linear regulator which feeds the PCH (Intel's Platform Controller Hub), or "southbridge", on a PC motherboard. It's working fine ...