All Questions
52
questions
0
votes
0
answers
28
views
Current Drawn from Bulk Capacitor at LED-Strip Output
I want to design a power supply (buck converter) which converts 9 V to 5 V and supplies it to the LED strip. The LED strip is a basic 1 meter long 70 LEDs/meter WS2812B strip. In my project, I want to ...
0
votes
1
answer
95
views
Should I limit inrush current of this MOSFET buck regulator?
I am building a digitally controlled constant current switching power supply. This circuit will deliver no more than 105 Watts at around 20V from an AC-DC DIN rail SMPS of 250W.
You can see and ...
0
votes
0
answers
45
views
5 V to 3.3 V buck with limited input current and large capacitor to cover current spikes?
We need to design a power supply for a 3.3 V WiFi-device. But there are quite some current spikes during WiFi startup. Using the design below there is a risk the 5 V (250 mA max) supply (not mine) ...
1
vote
1
answer
112
views
Using capacitor with voltage rating close to input voltage
I am using a buck converter in my design. The input voltage is 12V and output voltage is 5V.
The capacitor C331 and C332 are 10 uF 25 V in 1210 package. The inventory have already 16 V 0805 capacitors....
0
votes
0
answers
49
views
Choosing capacitors for Buck Converter – How many Electrolytic, How many Ceramic?
I am working on a high-power buck converter. This converter will be powering a purely resistive load (it’s a literal resistor – a heating element).
However, I am having some issues deciding how many ...
1
vote
1
answer
38
views
How to choose the right type and values of capacitors for LM5143A-Q1 output?
While learning and trying to make my first buck converter using the LM5143A-Q1 (datasheet link) from TI, I calculated the required capacitance at the output for the IC to be able to output 31A, which ...
2
votes
1
answer
130
views
Output Capacitor Design for a Multiphase Buck Converter
According to this application note from Texas Instruments, in the design of the output filter for a multiphase buck converter there are basically two ways of choosing the output capacitor. The first ...
0
votes
2
answers
218
views
use of capacitors and inductors in buck converter [closed]
For stepping down voltages, why can't we use a simple resistive circuit and the voltage division rule for the output? Why do we use a buck converter instead? What role do a capacitor and an inductor ...
0
votes
1
answer
90
views
When finding ESR/ESL of a ceramic capacitor, what frequency should I assume during a load step?
I want to determine the output droop in a transient load step for a buck converter I am designing.
The output capacitor will supply current during this load step, and there will be a drop associated ...
4
votes
1
answer
192
views
Questions regarding this power module
I'm looking at this power IC module.
I assume it's a buck converter. In that case, on page 16 of the datasheet, Equation 4.1, there's this formula: Rvout = 8.2 kΩ * TRIM. If TRIM is 5, then what would ...
2
votes
1
answer
1k
views
What is the function of the feedforward capacitor on the LM2596-ADJ?
I'm looking at the LM2596S datasheet and notice that on page 7 (figure 3) it recommends a "feedforward" capacitor for the adjustable variant.
The example schematic on page 9 shows a ...
1
vote
2
answers
187
views
Selecting capacitor and inductor for adjustable buck converter
I'm trying to understand how to choose the right inductor for a buck converter that can produce different output voltages.
When using an LM2596 I can add a potentiometer into feedback loop to produce ...
0
votes
1
answer
475
views
Buck Converter Voltage Ripple at Output
I just made a 32V to 16V 2 Amps buck converter with a 10mH inductor, I'm having an issue with the voltage ripple output. Too many spikes, and it's generally not consistent. Electrolytic and Film ...
0
votes
0
answers
385
views
What is meant by "Kelvin connected to capacitor" in layout terms?
In the MPS5496 PMIC layout guidelines on page 37, they mentioned that you should connect the feedback pins to the buck output capacitor "kelvin connected." What does that mean? Can anyone ...
0
votes
2
answers
236
views
What is the formula or any method to calculate the value of the output capacitor and inductor in a buck converter
I have using a buck converter whose output is 5V and 1A.
Can someone tell me whether these is any formula to calculate the value of the output capacitor? Like, without involving the switching ...