All Questions
Tagged with bottom-bracket hollowtech
13
questions
6
votes
3
answers
807
views
Broken plastic HollowTech II BB spacers, why?
Yesterday I was installing a BB-MT501 HollowTech II bottom bracket into my ~2006 Trek 520 frame. This frame has a 68mm BB shell.
I was following the directions on Shimano's website: https://si.shimano....
2
votes
1
answer
1k
views
What replacement for Shimano 105 SM-FC5600 Bottom Bracket
I have a Specialized Tarmac Comp bike from 2010. It has a Shimano 105 SM-FC5600 Bottom Bracket that I want to replace. It makes clicking sounds, after 50.000km of use.
I think I can use any shimano ...
2
votes
2
answers
402
views
Upgrade bottom bracket
I want to upgrade my bottom bracket (square taper 68x113 threaded) to Shimano hollowtech and fit a new triple crankset. My gears are 3x10 so will my front gears still work with the new set up.
What ...
5
votes
1
answer
927
views
Hollowtech II BB alternative for stripped frame threads [duplicate]
I removed the BB (Shimano BB-93) from my Canondale Trail and found the drive side thread is stripped on BB and frame.
See and
What are the options for me to replace the BB?
Is there an alternative ...
2
votes
1
answer
740
views
Dura-Ace R9100 Bottom Bracket With A Dura-Ace FC-7900 Crankset?
I have just purchased a Dura-Ace FC-7900 crankset and I am trying to find a good, readily available bottom bracket to pair with it.
With Shimano's Hollowtech II and Octalink II technologies, will the ...
1
vote
2
answers
951
views
How to install a Hollowtech II crankset if it does not fit the top hat?
In threaded 2-part bottom brackets there is a plastic top hat/bearing insert/dust cover that goes between the BB's bearing and the spindle, so that they fit tightly and the spindle does not wobble.
...
1
vote
2
answers
248
views
Misc bottom backet and crankset questions [closed]
I am planning to upgrade a few of my bikes .. some due to faulty BBs and some just to upgrade the crankset. Here are the questions I have:
1) Road vs MTB
I read from the another post about Road vs ...
1
vote
2
answers
693
views
External BB cranks not spinning well
I have a Cannondale F2000 that I'm updating and turning into a gravel/commuter bike.
I replaced the original square taper bottom bracket with a new Hollowtech II version.
Now the new crank does not ...
2
votes
2
answers
723
views
Upgrading a crank set
I presently have a 3x7 speed crankset with a sealed cartridge bottom bracket on my touring bike and want to upgrade to a new Hollowtech II bottom bracket and crankset, specifically, the SHIMANO Claris ...
1
vote
1
answer
3k
views
How to remove stuck Shimano Hollow-Tech bottom bracket cups?
When I tried to remove the bottom bracket bearing cups using the BB tool it was very hard to move or it's just stuck. Tried WD40 then slowly tapping the tool using a mallet didn't work. To cut the ...
2
votes
1
answer
684
views
Threading for BB (British) for Hollowtech 2 or square taper crankset?
I have square taper crankset from Sugino (compact double 48-34). I am using their aluminium cartridge BB (I think it's 68mm). Anyway, I was wondering what is the difference, if any, regarding the ...
2
votes
1
answer
3k
views
Using spacers on crank spindle instead of bottom bracket when fitting HollowTech MTB crank to road bb
HollowTech road BB is 68 mm wide and fits a road crank without spacers. Hollow tech mountain BB uses up to 3 x 2.5 mm spacers. Hence crank is designed to be used with 75.5 mm wide bottom bracket ...
5
votes
1
answer
3k
views
What types of BB-axle to crankarms interfaces are there?
On the lowest end, we have the taper/square interface. I believe it is standard i.e. there are no variations in the sizes.
image property of VP Components USA
Then there is the Octalink. Actually ...