Questions tagged [snmp]
Simple Network Management Protocol (SNMP) is used for managing devices on IP networks. It is most often used to query statistics for network equipment.
209
questions
0
votes
0
answers
86
views
Zabbix with Fortimanager
I am seeking assistance with configuring Zabbix to monitor FortiGates that are managed by FortiManager. Despite configuring FortiManager with SNMP and adding a host for it in Zabbix, I am not seeing ...
0
votes
1
answer
49
views
What is the difference between these OIDs on a Aruba Wlan Controller?
For my bachelors thesis, I have to monitor the WLAN Access Points of the university campus. For example, number of connected Clients and how many Clients are connected to each Access Point. Therefore ...
0
votes
0
answers
76
views
Is there a way to gather data of Optical Module Status and the CPU Utilization through SNMP protocol?
When using the snmpwalk command to query a Cisco SF302-08PP switch with the -c public community string, am not able to find data related to Optical Module Status and CPU Utilization. I am trying to ...
1
vote
1
answer
379
views
Cisco port channel identification through SNMP
on a cisco switch is there any way to identify, through SNMP queries, which interfaces are involved and configured in a port channel?
I did some experiment with commons MIB, without result.
Any idea?
...
0
votes
0
answers
83
views
Can I get ip-sla's destination IP address via snmp?
(Excuse my lack of networking knowledge as I am mainly a developer)
Is it possible to snmpalk to get a list of all ip-sla's destination ip address via snmp?
( Router: Cisco IOS XR Software (ASR9K), ...
0
votes
2
answers
578
views
snmpwalk returns hex-string for interfaces without a description
nterfaces with an actual description are returned as a string, for example the interface with Device1ILO
However the interfaces without a description configured, are returned as Hex-STRING 00.
How can ...
1
vote
0
answers
150
views
Can I check the security policies hit-count in juniper routers via SNMP?
Am trying to see if there is a way to get the output of "show security policies hit-count descending" via SNMP,
it has the following o/p like so,
show security policies hit-count descending
...
1
vote
1
answer
161
views
I upgraded a Cisco switch to a newer model with different SNMP OIDs. Can I have the new switch receive the old OID and report values from the new OID?
I upgraded from a Cisco SG300-10MP to a Cisco SG350-10MP. A piece of software is looking for the value from 1.3.6.1.2.2.1.8.50, but the OID on the new switch is 1.3.6.1.2.2.1.8.2. The final number ...
2
votes
0
answers
554
views
Cisco Access Switches: Monitoring AAA server dead via SNMP?
This is a new setup of Cisco access switches (2960S, 2960X IOS with 15.2(2)E9, but mostly C1000 with IOS 15.2(7)E*), with a Cisco ISE 3.0 as authentication server for 802.1X, config style is to be ...
1
vote
1
answer
211
views
Explanation about SNMPv3 USM
Context
I am having trouble understanding the USM model in SNMPv3. I base my research and understanding on RFC 3414.
My problem is that authentication is not enforced in some implementations of SNMP, ...
4
votes
1
answer
366
views
what are the difficulties of configuring switches through SNMP?
I have a cisco switch that supports CLI, SNMP, and NETCONF for management issues. I should develop an application for managing the switch which should include monitoring and also configuring ...
0
votes
1
answer
386
views
SNMPv2 to v3 conversion
Can I use a Cisco router to convert SNMPv2 from an end device in one network to SNMPv3 and the C&M software in another network?
The end device can only handle SNMPv2, but the C&M community is ...
0
votes
0
answers
48
views
snmp mib for monitoring service instance counters
in career ethernet switches like ME3600, we can configure EVC as defined in MEF.
evc counters(service instance counters) are as follow:
rx_green_frames; rx_green_bytes; rx_yellow_frames; ...
0
votes
1
answer
488
views
How can I monitor BFD flaps?
We need to monitor BFD flaps on our Cisco Nexus devices but the problem is that Zabbix do SNMP polling every 1 minute, and we can't detect, for example, 5 sec BFD flaps. We detect only if BFD down for ...
0
votes
1
answer
2k
views
How can I obtain SNMP OID from Arista in right way?
What is right way for obtain Oid from Arista?
I need obtain temperature from the switch. From this I find out that CPU sensor OID is .1.3.6.1.2.1.1.1.100006001:
switch#show snmp mib walk .1 | grep &...