Questions tagged [rip]
For questions about Routing Information Protocol (RIP).
83
questions
1
vote
1
answer
81
views
Rip Routing Protocol
RIP routing protocol use the distance vector routing algorithm that mean each router will share the distance information,But how can this distance information help the router to know where to forward ...
1
vote
1
answer
323
views
How can I implement BGP between two routers that have already been configured with different routing protocols?
I have two different AS with different IP ranges and subnets, and the first router stack is running RIP, and the second one is OSPF. I want to configure BGP between "Router-PT Router23" and &...
1
vote
1
answer
57
views
Import route from one rip group to another
Just started out with RIP implementation in juniper routers. Was not able to find much info on the following points. Any help is appreciated. I have defined 2 RIP groups, both in the same routing ...
1
vote
1
answer
48
views
RIP v2 Network Command
I am comparing the Boson ExSim Lab to the Neil Anderson's Lab on RIP.
On one of the labs on Boson ExSim, it asks to configure RIP on the routers, all of which are on some form of a 192.168..0.0/24 ...
0
votes
1
answer
470
views
Interior vs Exterior Gateway Protocols
I'm new to Networking and I was reading about the Interior and Exterior Gateway Protocols ,but i couldn't understand some points , as stated in a reference:
IGPs are designed to work in private ...
0
votes
1
answer
246
views
Doesn't OSPF Have Auto Summarization?
I asked AI if there is a command in OSPF for auto summarization like RIP and EIGRP. Here is the answer:
"No, OSPF does not have a command like RIP and EIGRP that enables or
disables automatic ...
2
votes
1
answer
400
views
Why No Ping When Use Static and RIP in This Network?
I am a learner. I learned somewhere that we could use static and dynamic routing in the network.
I built the simple network shown in the attached picture.
I configured router8 with static routes to ...
0
votes
1
answer
237
views
Packet tracer is changing my addresses ipv4
Could someone help me with this?
I have a subnet with the ip: 172.16.193.0 in the fastethernet 0/0 of my router and when I go to put it in RIP the Packet tracer is changing it for another ip:172.16.0....
0
votes
1
answer
111
views
Why I’m getting overlaps with fast Ethernet 0/1 when assigning an ip
But I have been receiving error code when I want to assist an ip to s1/0
1
vote
1
answer
209
views
Can ECMP be used with RIP?
I haven't seen anything about ECMP in the RIPv2 RFC.
Is it possible to use ECMP with RIP?
2
votes
1
answer
260
views
RIP routes are not being advertised
I have 2 routers(R3 and R4 connected with serial links). I have advertised my loopbacks with RIP ver 2. with 192.168.1.1/32 and 192.168.2.1/32 on R3 and 192.168.3.1/32 and 192.168.4.1/32 on R4.
My ...
0
votes
1
answer
36
views
Enquiries regarding securing strong password and ssh
I am a beginner in computer network and I have done some research with regards on how to do IP configuration on PC and routers. However, I am not sure on how to configure strong password and ssh based ...
0
votes
1
answer
183
views
Why does redistributing ospf in rip change the path of all routers on the rip network that are not directly connected to the router that redistributed
I have three routers connected to each other. Each has a subnet that it uses (eigrp, ospf, rip) as shown in the figure
I managed to redistribute EIGRP and OSPF, this works perfect. But when I try to ...
-1
votes
2
answers
348
views
why can't my PCs ping each other?
Consider the following network
I can ping just fine from PC0 to PC1 and PC2 to PC3, but I can't ping from PC2 to PC1 or PC3 to PC0. Why? I'll share the configuration from the router:
Building ...
2
votes
1
answer
450
views
Can't send message from RIP to static through BGP
Before deep into the question, please see this topology and the results of sending messages from one router to the other router:
I have succeeded in sending a message from R0 to R2 (or vice versa), ...