Questions tagged [zvs]
Zero-Voltage Switch driver, a.k.a. Mazzilli oscillator, a Royer-type resonant push-pull oscillator.
70
questions
4
votes
2
answers
404
views
Understanding the discrepancy between Input and Output power in ZVS Induction heater
I am using a ZVS induction heater like this:
Image Source
The schematic looks akin to this (schematic has not been tested)
Schematic Source
I modified it with IRF3205 N-Channel MOSFETs for better ...
0
votes
1
answer
41
views
Zero Voltage Switching (ZVS) in Conventional Full-Bridge DC/DC Boost Converter
I am trying to design a Conventional Full-Bridge DC/DC Boost Converter with the following parameters (I am not sure if you need them);
Input voltage: 24 V (DC)
Output voltage: 400 V (DC)
Output ...
0
votes
0
answers
58
views
How to choose Duty Cycle value for a Full-Bridge DC/DC Converter
I've noticed that while designing DC/DC converters, some sources (at the bottom of the website, comment of Benjamin Lough) suggest a "rule of thumb" duty cycle of 70%, while others (This is ...
0
votes
1
answer
64
views
Building a half-bridge zero-voltage switching inverter for induction heating
I am not an electrical professional so please me patient with me.
I'm trying to build a half-bridge ZVS inverter for a small induction heater (I want to try to do some small scale welding). I tried my ...
0
votes
0
answers
25
views
Regarding the equation derivations of the resonant state of an asynchronous buck converter observing zero voltage switching
I'm currently reading this article of Bill Andreycak to understand the mathematics behind zero voltage switching: https://www.ti.com/lit/an/slua159/slua159.pdf?ts=1710666811170&ref_url=https%253A%...
1
vote
2
answers
109
views
ZVS Circuit as LC Oscillator
I was wondering if a ZVS circuit would be suitable as an LC oscillator. I have used a ZVS circuit before for induction heating, and observed that the idle power draw was relatively high. I used a ...
3
votes
1
answer
123
views
Need regulated 15 kV output
I was just playing around with this ZVS circuit I made in LTspice. It was made to output 15 kV, but when I saw its actual output it had spikes of 25 kV, then it stabilized after a while. How to ...
1
vote
1
answer
116
views
ZVS low noise power supply?
I'm currently looking for low noise isolated DC-DC power supply for analog components. There are different variants available, like SN6501 IC or integrated DC-DC convertors. But I wonder, what if I ...
1
vote
0
answers
113
views
How is soft switching in a PMSM inverter achieved?
Recently I found some papers about PMSM drives that use the regular circuit of 6 e.g. IGBTs to drive a permanent magnet synchronous motor but with a resonant circuit in front of it to achieve zero ...
0
votes
0
answers
68
views
ZVS not working and doing weird things?
I recently made a simple ZVS circuit using 1w 15V zeners (BZX85B15-TR) , UF4007 ultrafast diodes, IXFH36N60X3 Mosfets, the capacitor consisted of a 3S3P setup with each cap being 680nf 250v film caps, ...
1
vote
1
answer
226
views
LTspice transformer not working as expected
I made this ZVS circuit on LTspice and want to make high voltages with it. The ZVS circuit does work fine and output high power but the transformer I made doesn't work fine. I want x400 step up which ...
0
votes
2
answers
79
views
Voltage drop across LC tank
I've been playing around with a ZVS circuit on Falstad, and it seems that the voltage drop across the LC circuit is based almost entirely on the size of the 2 inductors outside of the tank (the ...
1
vote
1
answer
84
views
ZVS driver not oscillating - powersupply
I'm using a ZVS driver to create a spark for a plasma speaker. The circuit above is the one I'm using for my project however I have run into some issues whihc I do not understand. First of all the ...
0
votes
1
answer
265
views
ZVS circuit to generate high DC voltage
I'm trying to design a high DC voltage generator to create a voltage differential between the upper and the lower part of a cloud chamber I'm building. I'm trying to use a ZVS circuit to amplify an ...
0
votes
1
answer
1k
views
LLC ZVS deadtime calculation
According to the TI LLC document, I can use eq 32 to calculate the dead time to achieve the ZVS in the half-bridge LLC Converter.
below is my spec of half bridge of LLC converter.
the deadtime I ...