Questions tagged [usb-c]
USB (Universal Serial Bus) Type C, a 24 pin connector system with a rotationally symmetrical connector. Consider using the "USB" tag in addition to this one.
527
questions
2
votes
2
answers
59
views
Replacing USB-C socket on a keyboard
I decided to fix some of my stuff that has broken USB-C ports. (why are they so fragile!) I've removed the old sockets and cleaned the pads, but when the old sockets were damaged (by simply inserting ...
1
vote
3
answers
71
views
How to install a USB-C PD host port on my electric longboard (54.6 V)
Installing a USB-C Port on a Longboard for Charging
I'm exploring options to install a USB-C port on my longboard to utilize its enormous ~400 Wh battery for charging my phone/laptop/anything.
Initial ...
0
votes
0
answers
51
views
Options after breaking USB-C jack off of PCB
Hello!
Snapped the USB-C jack off of my Logitech MX Keys.
I have a background in computer engineering and some experience doing board-level repairs. I do have an SMD hotplate, multiple soldering ...
2
votes
1
answer
68
views
FT230X using USB-C receptacle not working for data transfer
I have tried to add a USB-C connection to my PCBA solely for data transfer.
I have used a FT230XQ-R microchip (Datasheet) and followed their uploaded example for a USB-C receptacle. I have now ...
1
vote
0
answers
25
views
Low Quiescent Current over USB Type-C [closed]
I'm working on a battery powered project which I'm currently planning on powering over USB Type-C for flexibility. The 5V/3A spec would satisfy my needs for the high end of power draw, however, I want ...
0
votes
0
answers
23
views
ESP32, BQ25895 sharing usb data lines
Im building a portable device with a ESP32-S3 which will be interfaced with a SD card, and a BQ25895 charge controller. The ESP32 will connect to the computer as a mass storage device. The BQ25895 ...
0
votes
1
answer
49
views
USB Type C PD Minimum Requirement
I have been wanting to veer away from older USB connectors and start using USB Type-C receptacles in future designs but the standard is quite confusing as a hobbyist.
Searching the internet I see that ...
4
votes
2
answers
2k
views
Are USB-C through hole shell stakes connected to GND or are they just there for fastening purposes only?
I am looking to use a USB-C 2.0 16 pin SMT connector on a PCB. I can't find any information on the manufacturers site on whether the through hole shield/shell stakes are connected to ground. Do these ...
0
votes
0
answers
21
views
USB Type-C DFP Host Port implementation without Switch
I am currently designing a new board that has a four port USB 3.2 x1 Gen1 hub on it. I only need two ports and now thinkering how to best make use of the other two ports.
The idea was to make at least ...
0
votes
0
answers
32
views
USB-C module configuration pins in parallel connection
I have received a lot of help from several members of this site. After trying to wire two charging ports on the same device and investigating the diode OR-ing configurations and the power mux ...
0
votes
1
answer
51
views
Question about DC pin in USB C module. Is it possible to connect two USB C and Micro USB connectors in parallel to charge the same battery?
Good morning everyone,
I received help from several members of this page regarding my goal of adding a USB-C connector to a tablet that already has a micro USB connector for charging. After ...
1
vote
2
answers
144
views
Device is not charging (how to test ic)?
I have this USB-C rechargable vacuum cleaner. But 2 months after I replaced the battery for a bigger one (from 1500 to 3000 mah 18650) it is not charging anymore, it used to charge with the latter ...
1
vote
4
answers
97
views
Why USB-C plug doesn’t charge? [closed]
I have multiple USB-C 5V chargers of the same type that do not charge connected android devices. Devices detect charging if these are turned off, but when turned on, no charging icon of any visual ...
0
votes
0
answers
26
views
Troubleshooting power issue in LilyGo T4-S3 ESP32
I put a custom expansion board onto the nice T4-S3 devices' 2x15 header. But displaced by 1 pin (2 pins off) and shorted something out. Need help on how to troubleshoot and id the destroyed components....
0
votes
1
answer
65
views
What is the best way to adapt a larger connector when the insertion holes on the PCB do not match?
Good day, everyone. I have a Type-C connector on a device that is much larger than the micro USB connector I had previously. The insertion legs do not align with the holes on the PCB, and since it is ...