All Questions
20
questions
0
votes
0
answers
51
views
Options after breaking USB-C jack off of PCB
Hello!
Snapped the USB-C jack off of my Logitech MX Keys.
I have a background in computer engineering and some experience doing board-level repairs. I do have an SMD hotplate, multiple soldering ...
0
votes
1
answer
63
views
Seeking USB-C Female PCB Connector for Razer Kraken X Headphones Adaptation [closed]
I’ve recently undertaken a project to adapt my Razer Kraken X USB headphones from a USB-A to a USB-C connection. Originally, these headphones featured a male USB-A cable designed for PC connection. I ...
0
votes
0
answers
124
views
USB-C Pogo Pin Coupler Troubleshooting
I've been working on this project for a while now and have hit a bit of a wall.
I've been designing a magnetic cable coupler for a automotive device (Comma3X). The device communicates with the car via ...
0
votes
1
answer
223
views
How do you wire a usb type c female connector?
I'm modifying my Nintendo controller, and I need to solder some stuff onto the usb type c female plug. However, I noticed there are five pins, and I have no idea what a single one is. Could you ...
2
votes
2
answers
670
views
Is there any open source schematics for M.2 to USB Type C adapter?
Here are some pictures of what I meant.
Unfortunately there are no labels near the components.
0
votes
0
answers
166
views
How to set the transimission line impedance of Type-C to DisplayPort?
I have drawn a PCB adapter board to convert the Type-C signal to DisplayPort, using the CYPD3120 scheme from Infineon. The schematic is as follows:
(A clearer version can be found here Schematic.pdf)
...
1
vote
1
answer
816
views
Why is this USB-C cable working in only one orientation?
Background
I have a friend who, for the sake of his project, is wanting to lead a USB-C cable out from his USB-C Arduino into a PCB he designed. From there another USB-C port would sit outside of the ...
0
votes
1
answer
81
views
USB-C PD Smartphone
My scenario: USB-C 5V smartphone charger is connected via USB-C cable to an breakout board. Both breakout boards are soldered together (All A Pins to A and all B to B). So basically I only extended ...
1
vote
3
answers
330
views
Type-C as a source and sink
I am designing a circuit that consists of Type-C male and female connectors. The device will act as a bridge between the mobile and the charger. I connected the CC1 and CC2 to 5.1k resistors on both ...
0
votes
1
answer
136
views
USB Hub Self-Powered using USB Type C
I'm designing a board based on a USB Hub HS 2.0 that has five permanent attached ports, two of them with a high current consumption (180 mA typical, 250mA max. per device).
I would like the board to ...
1
vote
1
answer
139
views
Possible to separate D+ and D- on 2 layer board?
I am trying to make a PCB adapter, where the connections are USB-C, so need to cross connect the D+ and D- on both connectors.
Is it possible to run D+ on top layer, and D- on bottom layer?
Attached ...
0
votes
0
answers
73
views
USB-C cable PCB
I'm trying to emulate USB cable by FFC and Flat connectors ( I-PEX_20535-020E-02 ) but I don't know if it is possible use 2 layers for the pcb design. In TI Superspeed guides (SLLA414) they advice you ...
2
votes
1
answer
271
views
Can I connect and feed multiple USB-C breakout boards into a single USB-C board (for transmitting data)?
A USB-C breakout board (BOB) has VBUS, GND, CC1, CC2, D+, and D- pins. Can I "join" multiple USB-C BOBs together by connecting their individual lines in parallel and feeding them into a ...
3
votes
1
answer
563
views
How do I short D+/D- pads on usb type c connector?
I am working on a design which utilizes a USB type c connector. My question is what is the proper way of connecting the duplicate D+/D- pads? and do you recommend a specific trace width/ via size?
You ...
1
vote
0
answers
72
views
How to solder two USB-C female PCBs together?
I have two of these usb-c female sockets that I need to solder together to make a "gender changer"
https://www.amazon.com/gp/product/B00VJ944V2/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&...