Questions tagged [toggle-switch]
The toggle-switch tag has no usage guidance.
29
questions with no upvoted or accepted answers
2
votes
1
answer
83
views
Is there a way to make a 12 VDC, 5 A touch toggle button without a relay to control the load (5 A max)?
I need to find out if it is possible to make such toggle button to be used to turn on/off a load not bigger than 5 A at 12 VDC (car battery). Can a Z44N MOSFET handle this? Something similar to the ...
1
vote
0
answers
97
views
Latch circuit to cycle power in an ATX PSU
I'm designing a system powered by an ATX PSU. I'd like it to be able to be switched on and off by a momentary switch but also to be able to be turned off by another input.
The latch circuit is powered ...
1
vote
3
answers
67
views
SPDT switch mechanical drawing confusion from China vendor
I'm looking into this simple slider switch schema (MSK12C02), but I'm confused with the mechanical drawing here
Assuming legs labeled 1,2,3 from bottom-right ...
1
vote
0
answers
66
views
Switching large batteries between 12 V and 48 V connections
I have four 200 Ah batteries that I am using to drive two separate really high current loads. The first load is 12 V at around 400 A and the second is 48 V at around 120 A.
I was wondering if I could ...
1
vote
0
answers
228
views
Remote Operation of Toggle Switch
I'm working in a laboratory environment, where we need to change the state of a few toggle-switches from time to time. As we want more and more remote control in our lab, these toggle-switches need to ...
1
vote
1
answer
62
views
Old Sears Paint Sprayer In-line Switch Question
I have an old Sears paint sprayer compressor my late father gave me. It's model number 106.151210. According to the data plate, its 115V, 7 amps. It was sitting in the garage and one of my children ...
1
vote
2
answers
137
views
Switch battery usage off when jack 3.5mm is not inserted
I have an ongoing project where I'm using a condenser microphone to record various stuff, it's powered by a CR2032 battery and the output of the microphone is directed to a TRRS jack connector (3.5mm),...
1
vote
1
answer
288
views
Is it safe to toggle an LED strip powered by a 12 V ATX PSU line?
I connected a segment of an LED strip (12 V) to a line coming from a standard ATX PSU (the 12 V line, of course).
I just wonder if it is safe to put a toggle switch to turn on/off the LED strip, or if ...
0
votes
1
answer
39
views
Which switch supports 2 different input voltages and can switch between the 2 when outputting to a single device
I have a small heater that runs on a maximum 12v. I am using a PC PSU to power it. I want to know if there is a switch that will allow me to input 12v and 5v from the PSU and in one position of the ...
0
votes
0
answers
146
views
Transistor Latching Momentary Switch Help
Attached is a circuit for two "latching" transistor circuits using a momentary switch to toggle a relay. Switch 1/ Relay 1 works perfectly; toggles on/off as it should.
Switch 2/ Relay 2 ...
0
votes
0
answers
699
views
Push-button on/off controller for ESP32
I am trying to design a circuit to turn on/off the ESP32. When I press the button, the ESP32 will start and will not turn off until I press the button again.
Will this circuit work for this problem?
0
votes
0
answers
107
views
Giving write enable signal externally by DIP switch to FPGA memory
I have designed a simple internal SRAM memory where I initiate the write enable and read enable via DIP switches.
Verilog input wire has been declared in the simple memory read write which connects to ...
0
votes
1
answer
510
views
Relay open and close switch button automatically
I have a very simple circuit which consists of a battery, a load (lamp), and a button (on-off).
I want to a very simple and cheap (without Arduino or microcontroller) way to open and close the circuit ...
0
votes
0
answers
79
views
Improvements to a soft latching switch with battery protection
I'm building a modular DIY "smart battery pack" (I call it Kyoti - explanation another time,)starting with the on/off switch and basic under and over voltage protection built in. I know ...
0
votes
1
answer
71
views
What momentary switch should I use?
I want a switch that has 2 distinct non-momentary states (say UP and Down) and a momentary state. In both states (...