Questions tagged [test]
A definitive procedure that produces a test result.
16
questions
11
votes
5
answers
8k
views
What parts would one typically use for automated PCB testing?
I have a circuit board in production, primarily through-hole, to the tune of ~400 units per year. Each one is manually inspected and tested. The board has ten distinct voltage rails, four voltage ...
13
votes
4
answers
33k
views
How to test a crystal resonator in board?
I have 2 quartz crystal resonators in my pcb board: 32.768 kHz & 20 MHz. They are connected to a Freescale MC12311 transceiver IC, which has an HCS08 micro-controller embedded in it. I want to ...
5
votes
5
answers
2k
views
Stress testing an FPGA's power supply
I have an FPGA (Xilinx Spartan 6) for which I want to stress test the power supply in "steps" (e.g. the FPGA runs in loops of 1 seconds: full steam for 900 ms, halted for 100 ms) to check that the ...
3
votes
1
answer
3k
views
Test circuit for EU1640BCH12T / R Water proof ultrasonic sensors with Arduino?
I have EU1640BCH12T/R waterproof ultrasonic sensors, which I have got from this link. These are standalone raw sensors without breakout board and not a module like HC-SR04. Being a new electronics ...
2
votes
4
answers
2k
views
Is it feasible to test microprocessor/microcontroller?
What I can do if I want to test the microcontroller?
2
votes
3
answers
5k
views
How to test op amp stability?
I've got a circuit I'm developing using an op amp to drive a power MOSFET for an electronic load:
I'd like to test it for stability, but I don't have enough experience to know what perturbations are ...
19
votes
3
answers
89k
views
What is Full form of hFE of a digital multimeter?
In digital multimeter, there is a transistor-check function, and there is a term hFE. I do-not know how-to use-it, however, different Websites say it is a measurement transistor's gain ("the ratio of ...
13
votes
4
answers
10k
views
Continuity tests, risks?
Even though the electronic device is powered off, isn't there a risk of doing a continuity test on connections in the middle of the circuitry ?
I mean, you do apply voltage doing so - couldn't that ...
8
votes
9
answers
20k
views
Large difference between specced values and real values for LED strips?
Recently I bought some "300LED/5meter Waterproof 5630 SMD LED Flexable Strip" i.e. High brightness LED strips from China. In the specifications, it was said that the strip consumes 75W @ 12v, which ...
8
votes
2
answers
392
views
Calculate the resistances of all the possible connections inside a N-terminals black box based on measurements between terminals
Although it would seem that this is not the right SE for this thread since it is about creating an algorithm, the problem is actually about finding a systematic approach to the simplification of ...
3
votes
2
answers
26k
views
Testing the condition of an old sealed-lead-acid (SLA) battery
I have a small 3 year-old 6V 1.2Ah SLA battery that is used in a solar powered burglar alarm sounder box. The sounder recently stopped operating and the battery shows a voltage of about 4V so I am ...
3
votes
2
answers
4k
views
How can I test a hex Schmitt trigger?
Yay, me...I just got done soldering my first surface mount IC. Because I know how volatile heat can be, and with how close the tip of my iron was to the IC (especially without a socket!), I'd like to ...
1
vote
2
answers
244
views
How do I establish if an op-amp is bad?
I have a JRC2374 SOIC8 IC on my board which is not powering up. The IC seems to be involved in the power regulation switching operation. Here are the internals from the datasheet:
I know little ...
1
vote
3
answers
4k
views
Debugging I2C bus using an oscilloscope
Is it possible to debug an I2C bus effectivaly with a two channel (plus an external trigger) oscilloscope?
I've been trying to do it, to catch a single transaction starting from the start until the ...
0
votes
1
answer
106
views
How do I make a battery voltage indicator using the battery being tested?
I am trying to make a circuit that will test if a 5V battery is under 5V, with the testing circuit running off the battery being tested.
I have seen other answers to this question, however they rely ...