Questions tagged [software]
If your software question isn't electronics related, ask on stackoverflow.com
294
questions
1
vote
3
answers
74
views
Recertify against EMC (automotive E-Mark) due to software changes
There is a digital output control module with a CAN interface that I will be working on. Its already certified against EMC, e-mark (UNECE 10).
As the previous contractor will no longer support the ...
- 57
0
votes
1
answer
79
views
How to best use Micro-Cap?
Several users of this site recommended I switch to Micro-Cap for simulation. I'm having trouble with their schematic capture:
First, the symbols are very small compared to the text. Is there a way ...
- 1,135
1
vote
0
answers
15
views
How to display Wavegen output along with the scope, in AD2 using Waveforms?
I have an Analog Discovery 2, and am using it to study a couple of analog filters. I've created a sine signal from the Wavegen tool, and am probing the output on both the Oscilloscope channels.
From ...
- 133
0
votes
1
answer
71
views
PLM and handling software/firmware components
I need some help from any PLM experts in the community. I am looking for guidance on how to handle firmware/software releases in a PLM system. it seems that most of these PLM systems are geared for ...
- 71
0
votes
1
answer
88
views
Watchdog Timer doesn't play with input via Serial Monitor
I uploaded this very simple sketch to my Arduino Nano Every to isolate a problem I have.
...
- 339
3
votes
4
answers
3k
views
What software can I use to draw circuit diagrams like this? [closed]
Look at this beautiful circuit simulation, it is in the digital design class document that I received from my teacher.
I want to draw many circuits like that.
What software can I use to draw circuit ...
- 401
0
votes
1
answer
99
views
Tim5 initialization unable to trigger callback function on stm32
I've been having a lot of trouble lately trying to get ADC3 to run on my STM32F746g-discovery board, so I started from scratch in order to try to pinpoint a problem. Unfortunately, now timer5 isn't ...
- 91
0
votes
0
answers
148
views
How to drive TM1668 7 segment Control via STM32?
There is a curcuit diagram which is in the below. My aim is basically able to write these segments some numbers. For example, in Grid 2 side able to write 6, Grid 3 side able to write 7 etc. But my ...
1
vote
0
answers
81
views
MSP430 ADC sampling does not work right
I am trying to get the 12bit ADC of the MSP430F5529 working.
For this reason I want to read values from its internal temperature sensor every 2 seconds. The ADC setup is in the main.c file and the ...
- 47
0
votes
1
answer
162
views
Which is better for programming STM32F103C8T6? Using Arduino IDE or STM32CubeProgramming? [closed]
STM32 is can programming using Arduino IDE, but I am confusing about which is better for programming this device, and what is the deficiency about this two software for programming STM32. (I am ...
- 15
6
votes
0
answers
165
views
Vivante video memory size?
I'm using an NXP i.MX 8MP, with Vivante GC7000UL and GC520L GPUs. Using the Etnaviv open source drivers.
For the life of me, I can't figure out how much video memory is made available to the GPUs, nor ...
- 1,233
2
votes
1
answer
247
views
How to calculate the cut-off frequency of a software average filter
I want to read the voltage of a battery using an ADC connected to a PLC. The signal oscillates a bit and I want to smooth it. The ADC samples the signal at 860 samples per second and stores it in ...
- 407
1
vote
1
answer
342
views
Smart and Variable time step Micro-cap 12
I need to perform a transient analysis with the Micro-Cap software that gives me information about what happens in microseconds but also in hundreds of seconds.
Currently, I am doing several analyses ...
- 81
0
votes
1
answer
406
views
Do we have to set the ST-link v2 before using?
I was using the ST-Link V2 which shown below on the left side. When I connect it to the MCU's I/O, I could install the software and I could confirm that the software installed correctly from the ...
- 157
2
votes
1
answer
183
views
On a (Windows) PC, can the TxD pin on COM1 be bitbanged? If not, why not?
In this question:
Why usb to serial port converter can’t program avr microcontroller?
Cornelius claims:
"DTR and RTS are the only pins of the serial port that can be bitbanged."
But is that ...
- 63