Questions tagged [rs232]
RS-232 is the electrical standard used on most serial ports. Note that this standard is a +/- 15 volt system and requires a FDMI converter to make it compatible with TTL logic levels.
42
questions with no upvoted or accepted answers
3
votes
0
answers
403
views
Can RS-232 DB-9-compatible cable be used as a physical medium between two CAN bus DB-9 ports?
Note: I am not talking about connecting an RS-232 device to a CAN bus!
I am strictly interested in reusing a RS-232 cable with two DB-9 connectors (one male and one female) to connect two CAN devices, ...
- 145
2
votes
0
answers
335
views
Opto-isolated RS232 signal capture
I have a problem in which I need to capture (spy on) an RS232 signal through an opto-isolator. This isolator needs to be high speed since the RS232 signal can reach up to 115200 baud. The main problem ...
2
votes
0
answers
903
views
RS232 to TTL converter problem
I have a RS232 to TTL Converter which has 4 pins Vcc, Tx, Rx, GND . I am trying to make a serial communication with my PC. I have a AVR development board and I have tested my program by connecting ...
- 1,666
2
votes
0
answers
384
views
pic24fj128ga310 uart not working in application, but works with PuTTY
I'm trying to connect a PIC24FJ128GA310 mounted on an Explorer 16 board with an embedded wireless module. I have been able to set up both to communicate perfectly well with PuTTY (an equivalent to ...
- 21
1
vote
0
answers
50
views
RS232 isolated communication via MAX3250
I have a two diffrent boards. One of the board is send the SoC and other things to Charger Board. While charging progress starts I want to isolate this to device because battery ground is isolated to ...
- 27
1
vote
0
answers
157
views
PIC16F UART Receives only the first byte
I'm currently working on a PIC16F18855, I'm trying to set up the communication part.
My setup is as follows:
A PCB connected to my computer via a TTL232 cable.
The PIC16F18855 is clocked at 32Mhz, the ...
- 41
1
vote
0
answers
124
views
MCU to talk to 5 (or more) serials
I have a project where I need to talk to 5 devices over serial (RS232 to be precise).
At 57k Baud. With a polling frequency that is as high as possible.
The first step is probably to convert from ...
- 221
1
vote
2
answers
105
views
1
vote
0
answers
1k
views
Why don't LG RS232 commands work when the TV is on (only responds when off)?
I'm writing a new question after stumbling across this question which appeared to have similar symptoms:
LG RS232 Commands partially working.
As the other question noted, the power on command ...
- 49
1
vote
0
answers
150
views
Connecting RS232 GPS Board to Raspberry Pi
I purchased a NEO-6M GPS board to connect to my Raspberry Pi, and when I bought it I didn't realize that it was meant for RS-232 communication instead of UART TTL (which I believe is what the ...
- 121
1
vote
0
answers
213
views
Custom ATMEGA2560 with RS-232 Communication Problem
I made a custom PCB using ATMEGA2560 with 2 MAX3223 RS-232 ICs (because they were available to me) but only one Tx channel is working on both ICs and I can't receive anything on any of them. I tried ...
- 11
1
vote
0
answers
38
views
M-Bus level converter
Hello I am looking for an M-bus level converter. It has to support rs232 for hooking it up to a raspi. I have 5 slaves so 20 unit loads should be sufficient. I am not able to find a suitable product ...
- 137
1
vote
0
answers
88
views
UART communication with a Thorlabs chip
I am trying to configure a Thorlabs temperature driver (MTD415TE), using a UART-USB connection. For this, I am using a Foca v2.2 with a FT232R USB-UART cable. I am using serial terminals such as ...
- 11
1
vote
0
answers
670
views
RS-232 Level Shifter
Most PCs don't have RS232 built-in anymore. So the only option is USB-2-RS232 adapters or RS232 PCI-E card. While I expected the adapters to output a low voltage it turns out most RS232 PCI-E card ...
- 11
1
vote
0
answers
109
views
2x rs232 communication, single wirelss connection, also rs232 to control load cell perameters
I am struggling to find any information on the ability to have 2 rs232 connections with 1 wifi connection.
I have found this wireless chip, which supports, five Ethernet ports, two serial ports:
http:...
