Questions tagged [resistor-ladder]
The resistor-ladder tag has no usage guidance.
20
questions
2
votes
5
answers
1k
views
How to generate evenly-spaced config voltages from standard DIP switches using only passive resistors?
I am designing a circuit involving an LTC4316, which is configured by providing one of sixteen analog voltages on each of the XORH and XORL pins to set the upper and lower nibbles of its configuration ...
2
votes
0
answers
95
views
Adding level shifter circuit conflicts with other microcontroller peripherals
I'm working on a synthesizer with multiple functionalities (OLED I2C screen, encoder, audio, midi input, several keys input) on a Xiao RP2040.
I wanted to add a PS2 keyboard input.
RP2040 GPIO are 3....
0
votes
2
answers
111
views
Determining poles and zeros from those of interconnected two-port networks
My goal is to find the poles and zeros of a large network. Specifically a cascade connection of series C's and shunt L's. One could also consider this a CL Ladder circuit. I am interested in ...
0
votes
0
answers
45
views
Solving Resistor Array with Voltages at Nodes
Hello, I've been having a lot of trouble with this problem from my intro circuits class. The questions before this covered simplifying circuits by combining resistors. However, now that there's an ...
1
vote
2
answers
518
views
Frequency-dependent behavior of a resistor in time domain simulation
I know for a fact that to take into account frequency-dependent behavior in time domain simulation, equivalent electrical networks that reproduce the same frequency behavior are used, as it happens, ...
8
votes
7
answers
12k
views
What is the point of this resistor network?
What is the purpose of this resistor network? Why not just use one resistor? or connect the cathode of RA93 diode directly to the mosfet drain (this mosfet is high side of the h-bridge).
It seems to ...
2
votes
1
answer
3k
views
Any way to build Analogue Multiplexers using MOSFETs or JFETs or BJTs
Here's my requirement:
I need an analogue switch that can do SPST/DPST/DPDT with very low On-Resistance (<10mOhms). There would be current flowing through this switch, albeit in the range of a <...
0
votes
1
answer
141
views
Proving the output voltage of a resistor ladder only with usage of currents
I got the following problem. I would like to prove the the output voltage \$U_{aus}\$ of the following system.
I only want to prove it by using currents. So I don't want to use the formula for a ...
3
votes
1
answer
376
views
can I use a board that has resistor ladder buttons on raspberry pi?
I have a clock that has a circuit board with a resistor ladder setup for the buttons. I want to (disconnect the clock and) put a pi inside and use the buttons to control the pi. In normal use the ...
0
votes
1
answer
206
views
Using resistor networks as voltage ladder
Are there resistor networks which could function as a pre-made voltage ladder? In other words are there variations on how the resistor network is assembled, ie in series or parallel? I've found these ...
3
votes
1
answer
2k
views
Designing a car steering wheel interface, need to distinguish between two resistor ladders on the same ADC
I am designing an interface for my car steering wheel to a Android head unit, using a Sparkfun Arduino Pro Micro to handle the USB side of things. The steering wheel buttons use three wires and a ...
2
votes
1
answer
4k
views
Resistor ladder with Same resistor value and different resistor value
Im trying to connect 8 buttons to Arduino Analog input. I found its good to use input shift registers. But with my very basic knowledge I end up with resistor ladder. But Im a bit confused with ...
1
vote
2
answers
1k
views
Logarithmically-spaced resistances using switches
If you want a linearly-spaced set of resistances, you can use a ladder of logarithmically-spaced resistors and short out different combinations, as described here.
Is there a way to get a ...
0
votes
1
answer
181
views
How to replace microswitches with electronic switches in a voltage / resistor ladder circuit
Hello everyone,
I am relocating a pair of transmission control levers to a different location within a car. At present each lever actuates a pair of SPST microswitches (at the same time) ...
-2
votes
1
answer
881
views
Are there electrically controlled precision rheostats that are not solid state
I need precision variable resistors for a programmable analog computer that I'm trying to construct.
An analog computer requires variable resistors that can be set with precision.
I don't want to ...