Questions tagged [analog-switch]
An electrical component which performs a similar function as a mechanical relay (conducts an analog or digital signal when on but does not conduct when off). Unlike a mechanical relay, however, it has no moving parts, and it may or may not provide galvanic isolation between the control signal and the switching terminals.
134
questions
0
votes
1
answer
81
views
Analog switch for controlling LED
I need help/suggestions for the implementation of my schematic:
In the schematic image pasted below, particularly look only at the charging IC, boost converter, analog switch, and ATTiny 1616 ...
0
votes
0
answers
22
views
A scheme to control a number of ceiling light bulbs being on with a single switch [migrated]
I have a ceiling light with two bulbs and only two wires (live and neithral) arriving to it (220-250v AC) and a SPST switch. I want to connect one bulb directly to those wires and I want the other ...
0
votes
1
answer
43
views
Level shifter (floating shifting ?)
I'm currently studying level shifters, and I have a question: Is it possible to design a level shifter that translates 0 and 5 volts to VSS (e.g., VSS = 5V) and VDD (e.g., VDD = 8V)? If so, could you ...
1
vote
3
answers
134
views
Switch ELECTRICALLY SAFE between 3 resistive loads (16 A each) on a 16 A line
How to switch 3 resistive consumers (heaters), each having a current consumption of nearly 16 A alternate & ELECTRICALLY SAFELY (German standards)?
So that only one of them heats at a time and the ...
6
votes
2
answers
297
views
Analyzing Diode Quartet Switch
I am trying to understand how this diode quartet switch works. I am having trouble dealing with the two current sources. I can think about what happens to the voltages in the circuit, but how do I ...
0
votes
0
answers
37
views
Home a servo motor after power shutdown
Background: I'm trying to setup a servo motor 1171MG with a 555 timer and finetune the position with a potentiometer as it depends on various project aspects.
The circuit is driven by a small board &...
0
votes
0
answers
32
views
Power selector for 12V car battery and Li-Ion
I am currently using the following power selector circuit (based on this Microchip app note) to switch between a 5V (5V5A) supply and a Li-Ion 3.7V battery (...
0
votes
0
answers
29
views
Better switch/mux type for laser diode
I recently designed and tested a laser driver board which can generate max 200mA current. One of the requirement was to be able switch that current source between 4 laser diode channels. I used ...
0
votes
2
answers
66
views
Switching circuit with logic 3.3V control on p-channel JFET
The task is to derive sinewave (of higher frequency) chopped by step-function (also periodic but of lower frequency, i.e. several periods of sine wave are placed in that pulse). So I have a sinewave ...
0
votes
1
answer
144
views
Timed momentary switch modifier
I would like to design a circuit that adds a power off delay
What would you suggest, is it possible to solve that basing only on the circuits batteries? Modifier from the market uses own 9V power ...
3
votes
6
answers
1k
views
Simplify one-time switch made using a flip flop
I'm trying to make a one-time, "turn-on-once" switch. I've made a simpler design before, but I seem to have lost it.
So basically, when the comparator is pulled to high, the switch turns on ...
4
votes
2
answers
544
views
Analog switch for AC
I'm looking for an analog SPDT switch which will block reverse current if in open state.
The circuit operates in two modes:
LED on (SW1 and SW2 in closed state)
LED off (SW1 in closed, SW2 in open ...
0
votes
1
answer
84
views
How to correctly switch between two analog signals before op-amp
I have two sources to generate a ramp signal to drive a voltage controlled oscillator.
Source one is DAC of the STM32H743 and the second one is RF Synthesizer ADF4158's charge pump output.
RF ...
1
vote
1
answer
60
views
SN74LV4052APW as UART Switch
I am using SN74LV4052APW as UART switch with ESP32-S2 SoC Design. I have 3X UART in the design but since ESP32-S2 supports only two UART channels so I had to use this electronic switch to switch ...
1
vote
0
answers
53
views
How do I interpret this analog switch logic diagram?
The following is the logic diagram of a single pole double throw analog switch that I am trying to use.
Specifically what I am wondering is if it connects one of nY ...