Skip to main content

All Questions

Tagged with
1 vote
2 answers
54 views

Low power low speed pulse divider?

I have a digital input which receives irregular pulses. I want a circuit that takes that input and generates an output pulse for every 100 (or so) input pulse. The expected input speed is 10-300 Hz. I ...
Alexander Ohm's user avatar
2 votes
3 answers
737 views

Why is my op-amp pulse generator (LF353) delivering way less voltage (±2 V) than the voltage supplies of the amplifier (±15 V)?

I had to design the following circuit as a pulse generator so that if I vary the resistance the frequency will vary as well. It's defined by the frequency expression: $$f=\frac{1}{2R_4C_1\ln(3)}$$ ...
ronny's user avatar
  • 83
3 votes
2 answers
297 views

Output with programmable rise time

I am tinkering with a device to generate pulses for a measurement setup. No need to buy it: Just wondering how one would implement it. Idea: Device generates a square-wave (Vpp and DC-offset) output ...
ElectronicsStudent's user avatar
0 votes
2 answers
81 views

Reducing the signal frequency

I have a sawtooth signal: roughly speaking, the duration of the "tooth" is 1 ms. Is it possible in the analog world to thin out this signal? For example, leave only every third, tenth "...
dahaha's user avatar
  • 5
-1 votes
2 answers
322 views

Peak/envelope detector circuit for 30 MHz sine pulses with a 10 kHz PRF

My goal is to input 30MHz sine pulses, with a pulse width of 10us and gap of 90us between the pulses. The circuit should convert this pulse train to a TTL signal that goes from 0 to 5 volts. To ...
fisherman's user avatar
0 votes
1 answer
799 views

Square wave distortion on low frequencies

I have this old Soviet low frequency sine and square pulse generator "G3-36A". I ran into an interesting problem. When I try to generate square pulse under 100Hz I get a distorted wave. ...
kawasaki997's user avatar
1 vote
2 answers
492 views

Convert a continuous voltage to a pulsed voltage

I have a continuous 5V voltage which I would like to switch ON/OFF at a certain frequency. The output should be between 2V - 5V, and the minimum duration between ON/OFF should be 1 ms. The control ...
Vimanyu's user avatar
  • 11
-2 votes
1 answer
401 views

What electronic component can send pulses? [closed]

In analog hardware synthesizers, an electric pulse is sent by an oscillator to a sound-emitting device for it to create sound at the desired frequency. What device generates this pulse? What is the ...
GPWR's user avatar
  • 115
0 votes
0 answers
123 views

Low-pass (band-pass) filter for op amp circuit

I have a circuit that amplifies a one-shot inductive trigger pulse of about 1.3Khz (@780 micro sec period) from about 10-200mV to about 3-4V. Between C1 and R3 there is a 0.13uH inductor coil with 11 ...
TommyS's user avatar
  • 135
1 vote
1 answer
84 views

change in ac reading relative to the frequency

I'm working on a school project, just measuring the Vrms of two different waveforms at different frequencies. The function generators output is connected directly into an oscilloscope therefore the ...
Curious Student's user avatar
0 votes
2 answers
106 views

what is this type pulses called?

I was wondering what is this type of pulses is call. Is it a sin wave? I know its the result of sinusoidal pulse modulation. is it considerd a quasi-sin wave? I would like to know the name to ...
Anwer Ak's user avatar
0 votes
2 answers
288 views

Pulse width for mark pulse

What is the pulse width for the mark pulse in an equal mark to space ratio pulse train operating at a repetition frequency of 5 MHz? The answer is suppose to be 100 ns .But I didn't understand how to ...
Jarvis Ferns's user avatar
-5 votes
1 answer
208 views

frequency counter [closed]

I am an amateur in electronics and am going to make an RF frequency counter. So after searching, I selected this circuit but my input signal is RF while the input of the circuit is a pulse. For ...
HFAR's user avatar
  • 1
0 votes
1 answer
120 views

Does a RF frequency multiplier work with ultrashort pulse?

The question is, does a RF frequency multiplier work with ultrashort pulses? In another words, does the frequency multiplier change the pulse width of input signal? For example, suppose we have a ...
user176585's user avatar
0 votes
0 answers
76 views

minimalistic digital 2-speed oscillator with 555

I'm trying to figure out how I can turn a schematic of a one-speed simple 555 astable multivibrator that's available everywhere on the internet to a digitally controlled astable multivibrator in which ...
user avatar

15 30 50 per page