Questions tagged [load]
An electrical load is an electrical component or portion of a circuit that consumes electric power. This is opposed to a power source, such as a battery or generator, which produces power.
578
questions
0
votes
1
answer
77
views
120 Vac, three phase, 400 Hz power supply - how important is balancing load?
We have 208/120 V, 400 Hz outlet. Can I use a single phase from the outlet to power my hardware or do I need to maintain equal load on all phase?
Let's assume that the max current draw is around 6 ...
2
votes
0
answers
87
views
Crystal Load capacitors & ESR
In the KSZ8863 datasheet, the crystal specification is given (table 9-3), page 85.
Here the ESR is specified to 40ohms with no minimum nor maximum marking.
Load capacitance is specified to a max of ...
0
votes
1
answer
126
views
Looking for alternative analog/digital circuits to drive low impedance with high current
I am looking to drive a load with the specifications as follows:
Load Resistance = 2.2 ±0.3 Ω
Load Current = 1.5-4.5 A
Nominal Load Current = 2 A
The load current should never go below 1.25 A at any ...
0
votes
3
answers
515
views
Voltmeter reading over 63 amps with no load attached
Please see the attached pictures. I am new to electrical stuff and experimenting. The meter in the attached pic shows over 63 amps with ZERO load attached. Is this meter damaged?
1
vote
1
answer
179
views
Does car alternator speed increase during load dump?
I am trying to understand the mechanism of voltage surges during load dump in automobiles.
As per this article -
The load-dump event has two components. First is the pulse amplitude (VP), which ...
2
votes
3
answers
101
views
Utility of a load resistance for measuring another resistance
In this paper they need to measure the value of an unknown resistance RS, whose value is the output signal of a sensor. However, instead of measuring this resistance directly with a multimeter, they ...
0
votes
1
answer
2k
views
How to wire a 6-pin relay?
I have the relay described in this datasheet. I have the z-type. It has 6 pins on the bottom.
I want to control this relay with an Arduino device and all it has to do is work like a switch.
simulate ...
5
votes
6
answers
2k
views
Purpose of 1 kΩ resistor in parallel with load at output of op-amp
As I was reading some op-amp data sheets, I noticed they placed output resistors to ground in some test circuits. These can be seen in the insets of the plots below for the LTC6228 and the LT6202.
...
0
votes
0
answers
102
views
Loading problem with circuit simulation
EDIT #1
So I understand now the phenomenon that is happening.
Taking operational stage 2 Switch is OFF.
So there are the 2 cases discussed.
RL = ∞ (exaggerated scenario) the current I1 >> I2 ...
1
vote
3
answers
2k
views
P-Channel MOSFET used as a load switch, practical doubt about Vgs
UPDATE AT THE BOTTOM
in a battery powered project with high current I'm using a P MOSFET as load switch in place of a mechanical switch to prevent inrush current and consequent spark on the switch ...
4
votes
3
answers
2k
views
If batteries are arranged in series in a closed circuit (I.e. with a load, which is constant) why doesn’t the current increase when voltage does?
I guess people have asked slightly similar questions to mine before, but I still haven’t been able to find a complete answer as to WHY the current doesn’t increase even when the voltage in a circuit ...
0
votes
1
answer
43
views
Volt/load meter - DAQ question
I have an analog output from a FANUC Variable Frequency Drive that gives a voltage in the range 0-10v depending on the load. I've cut & paste the relevant parts of the manual below.
I would like ...
1
vote
6
answers
397
views
Solar seller provided wiring diagram: Is this diagram of any use or unreliable/inefficient?
A solar equipment seller provides this wiring diagram (not mine):
There are three terminals on the solar charge controller: Solar IN, ...
0
votes
1
answer
708
views
ESP32 and TP4056 lipo charging
I'm currently working on a project involving an ESP32-S3 Microcontroller. I want to implement a few things that are very hard for me to figure out. This is my current TP4056 charging logic + battery ...
0
votes
1
answer
128
views
I am simulating an equivalent model of a laser in LTspice shown below. I am supposed to plot the power at node Pout versus the input current
The issue is I am not able to plot the power without adding the load resistor which is not specified in the equivalent circuit.
Is there any other way to plot the power? If not, then what value of ...