Questions tagged [conformal-coating]
Conformal coating is an insulating material applied to PCBs to protect against damage to the electronics. You can use this tag for questions about protecting PCBs with conformal coating and for issues with debugging/editing PCBs which have already been conformal coated.
45
questions
20
votes
7
answers
54k
views
What's the best way to protect a board from corrosion in a hot/moist environment?
Some of my projects need to live outside for long periods. Sometimes, moisture gets into the enclosures. That means that a circuit board might be sitting around in contact with water for hours on ...
15
votes
10
answers
2k
views
Does this exist: Insulating material to cover circuit
For example when you build a circuit you have the board and the components between them is air.
Is there a clay like material that will act like air does?
Application: you could bundle simple ...
11
votes
5
answers
3k
views
Making a device explosion proof
I am working on prototyping a gas leak detector device to be used in homes, it should have two small windows in the casing to allow sound to go out and the other window allows gas to reach the sensor.
...
9
votes
2
answers
745
views
Pour-and-drain conformal coating as an alternative to potting
Is there a standard process to pour conformal coating, similar to potting, but then drain the excess? The benefit of draining the excess is to reduce weight and get better cooling.
From my limited ...
7
votes
3
answers
1k
views
Should I re-apply conformal coating after hot air soldering?
I'm working on a PCB of a drone. It had some failed MOSFETs that I've replaced using hot air soldering.
It works fine again, but parts of the PCB were covered in a glue-like substance which I think ...
7
votes
1
answer
268
views
Acceptable conformal coating expansion ratio for PCB with delicate SMT parts?
I have heard that conformal coatings can put stress on SMD parts because of expansion/shrinking while curing or because of temperature differences. How much of a problem is this?
The only value ...
7
votes
2
answers
813
views
Conformal coating and micro SD card sockets
I have a embedded computer design which uses a low profile micro sd card socket as an extra option in addition to an on board solid state disk as storage/booting mediums. In manufacture the board is ...
6
votes
1
answer
1k
views
Can you tell me more about "re-enterable" potting compound?
I heard the term "re-enterable potting compound", which is a gel-like (possibly hard?) material that can be used to fill electronics enclosures for water intrusion protection and other things.
What ...
5
votes
3
answers
1k
views
Clean vs no-clean for high voltage circuit
I have a board that has fairly high working voltages up to 100V with small clearances down to 12 mil between the high voltage and ground or low voltage nets. This is unavoidable because the whole ...
5
votes
1
answer
364
views
Conformal Coating Shielded RF Module
Re: Conformal coating of shielded RF modules
I have an IoT device that consists of a PCB that goes inside a watertight enclosure. The device will operate under constant water, since it will be ...
5
votes
2
answers
1k
views
Humidity design requirements
I have to design a electronics device that is specified for environmental operating conditions of 0°C to 60°C with 5% to 95% relative humidity (non condensing).
I think the temperature part should be ...
5
votes
2
answers
1k
views
Waterproof enclosures
I have a simple farm gate monitor which I'd like to put in a rugged waterproof enclosure to keep it dry enough to operate outside for approximately ten years with no maintenance other than the ...
4
votes
3
answers
4k
views
PCB opaque coating for anti reverse engineering?
Im trying to find a coating for my PCB in order to protect it from reverse engineering. I want it opaque, non-conductive and with a low thermal resistance.
Basically I do not want that someone ...
4
votes
3
answers
4k
views
Removable/soluble potting compound?
Are there removable/soluble potting compounds that are moisture-proof yet removable without damaging electronic components? I've been able to plunge-mill potted devices to get near enough to ...
4
votes
1
answer
315
views
Conformal coating of UHF (radio frequency) circuitry 400 - 1000 MHz
Do you have experience applying conformal coating on UHF circuitry (ISM band)?
Are there known issues (e.g. degradation of UHF performance) which arise when coating UHF components like filters and ...