Questions tagged [configuration]
The configuration tag has no usage guidance.
118
questions
2
votes
2
answers
43
views
12V through USB Type C without PD
Can I get 12V to my system through USB type C without PD or configuration CC lines or Using CC controller?
If yes how can I do that .
- 21
0
votes
1
answer
60
views
Altera FLEX 8000: Extracting "bitstream" from .sof file?
I've acquired an Altera FLEX 8282A FPGA and I'd like to have a bit of a play with it.
Yes, I know these are prehistoric parts, but I like playing around with old stuff. :-)
I've installed MAX+Plus II ...
- 183
1
vote
0
answers
24
views
LIS2DE12 configuration for interrupt when going from stillness to motion and vice versa
I'm having difficulties understanding how to configure the LIS2DE12 for generating interrupts. Especially the filter part is obscure to me.
The task is to make the accelerometer generate an interrupt ...
0
votes
0
answers
34
views
Composite Node Configuration in a Lin Description File
LDF (Lin Description File) is used to describe a LIN (Local Interconnect Network) cluster. Since LIN 2.0 there is a definition of composite nodes in a LDF. A composite node allows a definition of a ...
- 103
0
votes
0
answers
52
views
Simulating a controlled rectifier with CMOS , using Isis Proteus
I am currently in the simulation phase of a controlled rectifier, and I must use CMOS technology. However, I am a novice in this field and would appreciate detailed advice to help me get started. ...
0
votes
1
answer
36
views
Where to apply input source to common gate configuration
I have learned from my teacher that the input of the common gate is applied at the source pin and the output voltage is probed from the drain pin, why not vice versa? Can I do that?
- 1
1
vote
0
answers
31
views
Help in system initialization and clock configuration of MSP430F427A MCU interfaced with custom LCD
When I debug the code, the LCD refreshes rapidly. I am not confident with the correct system clock configuration to use. Moreover, after debugging, in release mode, nothing displays on my LCD nor the ...
- 21
1
vote
1
answer
61
views
How do Altium Designer 20.2.4 Schematic Defaults work?
I'm trying to use the Schematic -> Defaults to predefine how I want every part of my schematic, but I found it a bit confusing.
First of all, I can't make the changes that I want. Now I'm trying to ...
0
votes
1
answer
42
views
XLamp XHP70.2 LEDs Configuration issue
I was reading the XHP70 LEDs datasheet where there were two configurations given, 6V and 12V. I am having a confusion whether a single led is rated 6V/12V or a combination of LEDs are rated this way ...
- 669
3
votes
1
answer
245
views
1.2/50 us Combinational Wave Generator (Surge Test) Simulation - Help Needed
I am looking for assistance in editing my LTspice simulation for the design mentioned in the title. I have provided the design and output (open + short circuit) expectations (First two screenshots), ...
0
votes
0
answers
105
views
How to chose the correct value for configuring burst ETH-DMA accesses for STM32F207?
I'm checking the default configuration of an ethernet communication project based on STM32F2 microcontroller (stm32f207 RM0033
UM). Where the comments I'm gone to do, they could be find on section 28....
- 851
4
votes
1
answer
153
views
BASYS3 FPGA pin planning and configuration question
I have designed a basic 8-bit CPU that is mapped onto FPGA fabric on a Digilent BASYS3 development board. The DRC results in a few error messages that I do not understand, with one of them being shown ...
- 1,555
0
votes
1
answer
113
views
Why does the USB specification have 3 different system power configurations?
I was reading about USB specifications/configurations from this PDF.
On page 5 it says that USB power configuration can be achieved (can be configured) with 3 different power options.
I have utilized ...
- 3,404
1
vote
1
answer
411
views
Understanding the implications of STM32 pinout configuration conflicts (yellow triangles) in CubeIDE?
Using CubeIDE and configuring STM32L072 I get some (yellow triangle) GPIO conflicts on my I2C2 interface. The GPIO's are assigned to other non I2C uses. Where would I look to understand the ...
1
vote
1
answer
2k
views
What is the Intel FPGA configuration file .pof used for, and how is it different from the file .jic?
The Intel FPGAs have a number of different programming files, among these the files:
.pof (Programmer Object File)
.jic (JTAG Indirect Configuration)
I know that the file .jic can be used to program ...
- 579