Questions tagged [buck]
A non-isolated DC-DC converter topology which outputs a voltage less than or equal to the input voltage.
324
questions with no upvoted or accepted answers
1
vote
0
answers
28
views
Getting "Too few nodes" error
While I am trying to simulate this LM5164Q buck converter IC exported from TI, I'm getting the too few nodes error. How to rectify it?
1
vote
3
answers
61
views
Input capacitance estimation for a buck converter
To estimate minimum input capacitance required for a buck converter to help with power stability & noise suppression, I came across below equation by TI.
https://www.ti.com/lit/an/slyt670/slyt670....
1
vote
0
answers
41
views
Running a Motor Controller, Motor, and Raspberry Pi off the Same Power Supply
I have a 24V brushed motor, a Raspberry Pi, and a Teensy 4.1 microcontroller all running off the same power supply (a 24V tool battery). I have a step down regulator that converts 24V to 5V:
https://...
1
vote
0
answers
99
views
Input filter for switching regulator
I'm trying to create an input filter for a switching regulator for automotive application.
My aim is to make a supply board, where from 24V come out 12V (from the buck) then 10V and 5V (from two LDOs)....
1
vote
0
answers
105
views
Best way to control large buck converter?
I am looking for a faster way to control output voltage for a buck converter.
This buck converter has its own fet driver and I am not willing to change it. I really only need the signal to run the ...
1
vote
0
answers
766
views
How do I properly import a .lib description into a LTspice symbol?
I am trying to simulate the TI part TPS62808 in LTspice, Pspice for TI, and Tina TI. I managed to easily run the simulation in the latter two simulators, but the models were specifically made for them,...
1
vote
1
answer
209
views
Using a capacitor to handle the inrush surge power of a fridge
I have a household mini fridge connected to my off grid electrical system, and recently I bought a smaller inverter just for the fridge so that I can turn my larger inverter off to reduce power ...
1
vote
0
answers
62
views
Unable to find Gvd of a buck converter using LTspice
I'm trying to simulate a closed-loop buck converter in LTspice. I'm using ideal components. I started by finding the Gvd of the buck converter (duty to output transfer function). I used the .ac ...
1
vote
0
answers
288
views
Modifying XL4015 CC/CV Buck Converter for Undervoltage Lockout
I am trying to convert a XL4015-based CC/CV buck converter module to CV with undervoltage lockout. At this point I am hoping someone can double check my schematic for glaring errors before I attempt ...
1
vote
0
answers
105
views
The best way to step down 12V to 5V with at least 10A current from a PS3 power supply for a WS2812B LED strip
I am new to electronics. I had a PS3 Super Slim power supply lying around, which outputs 12V up to 13 amps. Recently, I bought a 5-meter strip of WS2812B LED strip, which needs 5V, and the recommended ...
1
vote
0
answers
46
views
Are the prinicples the same for designing a high side vs low side buck?
I am an analog engineer that is getting into SMPS design.
This is a high side buck:
This is a low side buck:
simulate this circuit – Schematic created using CircuitLab
Assuming that I take ...
1
vote
0
answers
62
views
Synchronous buck battery charging circuit using totem pole gate driver
Background - We are trying to develop a very low cost buck (day time)/boost (night time) converter for charging LFP batteries (day time) and powering LED (night time). Due to cost impact we are trying ...
1
vote
0
answers
45
views
Noisy signal output from BD2320 MOSFET driver
I need help or technical solutions relating to this issue I encountered with BD2320.
I intend to use two BD2320 drivers for an interleaved buck converter. One of the channels works well, but after ...
1
vote
0
answers
33
views
Zero due to ESR in buck converter
How come the equation given leads to one answer for the zero location (marked 1) whereas my intuition leads to another (marked 2)
1
vote
1
answer
178
views
How do I use the TPS5403 DC-DC buck to get 3.3V output from a 5-15V input?
I am trying to use the TPS5403 (datasheet) buck converter to power an ESP32 at 3.3V from an input of 5-15V, however, I can't find enough resources online to be sure in my design.
Below, I have ...