Questions tagged [adapter]
In electronics the term adapter is normally used to describe something that converts from one connector or package to another. For example a BNC to SMA adapter is an example of a connector adapter, while an SOIC to DIP adapter is an example of a package adapter.
448
questions
-2
votes
0
answers
34
views
I need help in 68HC705 programming [closed]
I want to burn some 68HC705C8 chips. I am grateful for any help or information.
0
votes
1
answer
52
views
How can I make an adapter wiring for a TRRS microphone to TRS?
I'm making a sound level meter using a Raspberry Pi as part of my thesis. My professor has given me a TRRS microphone to work with.
I tried to make the TRRS microphone work with the Raspberry Pi ...
0
votes
1
answer
40
views
Best practices for combining dual mono to stereo? [closed]
I have two old-style telephone pickup coils, each of which has a 3.5mm mono (TS) male output. I made a simple adapter that just runs together the grounds from both inputs and connects each positive to ...
0
votes
1
answer
91
views
Prolific PL2303 knock-off USB-TTL adapter without timing crystal
I recently got this bare-bones USB-TTL adapter which unsurprisingly contains a knock-off Prolific chip but on top of that it is entirely without the crystal oscillator. It seems to be missing some ...
7
votes
4
answers
867
views
Characteristic impedance of a BNC jack to jack adapter
I have this BNC jack to jack adapter. I want to measure its impedance but I am reading around 1mΩ. The datasheet says that it is a 50Ω adapter.
Why am I measuring such a low resistance?
3
votes
0
answers
73
views
Designing a U.2 to M.2 NVMe adapter
I'm considering designing my own U.2 to M.2 converter card to make use of the four U.2 (PCIe 3.0 x4) connectors on my motherboard. Commercial products are available for doing this type of conversion, ...
0
votes
2
answers
54
views
If I provide this wall power strip 240V 50Hz instead of 120V 60Hz, what do I get back out? [closed]
I'm looking at this product, and next to the plug, it says:
Input Voltage: AC110-250V
Maximum Power: 2500W 10A
USB Output: Total Max 3.4A
Frequency: 50/60Hz
It ...
1
vote
1
answer
159
views
How to design an SD card to Memory Stick adapter?
I want to design an SD card to Memory Stick adapter. I will need to somehow implement SD controller (host) and Memory Stick controller (device) in my design, then do the translation between the ...
0
votes
1
answer
32
views
2 Row Ribbon Cable Connector Pin Swap
I have two different LCD displays that uses a 2 row, 16 pin connectors. For reasons unknown, one of the designs has customized the connection and implemented a pin swap that makes using an off the ...
0
votes
0
answers
45
views
How to check if I destroyed the bluetooth receiver
I have very little experience with electronics but I tried converting my Logitech unifying receiver to USB-C.
I followed the steps I found online and got a functioning result. I based my wiring on the ...
0
votes
2
answers
82
views
Is my 600mA, 9V adapter suitable for a MB102 breadboard power supply?
I've recently bought a 600mA, 9V adapter thinking that it would be suitable for a MB102 breadboard power supply but have now read that the maximum output of the MB102 breadboard power supply is 700mA ...
0
votes
1
answer
82
views
Old piano Power adapter [closed]
I bought an old Roland EP-9e digital piano from eBay. The seller mentioned that it was missing a power supply. I purchased a matching power supply, 12V DC 2A. However, upon trying to plug it in, I ...
0
votes
0
answers
104
views
How to make a recent laptop touchpad work on PC with an external PS/2 USB adapter
I want to make a laptop touchpad work individually with a USB adapter, but failed, on a recent Thinkpad E14 touchpad part.
Some articles on the internet said they succeeded connecting the touchpad ...
0
votes
0
answers
28
views
Power adapter output voltage detection [duplicate]
Not sure if this is right place for this question, but since I don't know where else to ask, I will do it here anyway - if this is wrong exchange, please let me know ...
I have 35 W phone charging ...
0
votes
0
answers
45
views
Calculate power adapter to use [duplicate]
My wife acquired second-hand model houses with lights and an single adapter which had 5x DC power outputs, one for each house to light up. She was using it and the adapter started to smoke and catch ...
1
vote
1
answer
256
views
Split a single power source to act as two independent power sources?
Disclaimer: I'm very new to electronics.
I am building a Bluetooth speaker using an ESP32 dev-board and an I2S DAC which outputs to the audio-amp and then the speakers. I am using a 12 V, 3 A adapter ...
1
vote
0
answers
56
views
PCB Adapter for different signals
I need to use a connector that only exists in a version for PCB installation, but I have to connect it to a cable; so, I was thinking of making a small adapter PCB on which to directly solder the ...
0
votes
1
answer
61
views
How to wire Emerson AC/DC Power Supply in USA? Came with a Chinese power cord
I'm trying to wire up this AC to DC converter and have never seen the connections that this thing came with.
The converter is an Emerson R48-3200.
The label shows AC input 200-250 Vac 18 A 50/60 Hz.
...
1
vote
1
answer
100
views
What kind of package is this? Expected a tsop flash but I don't know
I'm a beginner in the electronics world. I opened this Chinese bootleg Sega genesis cartridge and in the place I expected to find a tsop flash chip I found this kind of adapter board with a package ...
3
votes
3
answers
170
views
Bypassing battery to power car while camping [closed]
I'm considering going camping but I only have a car, not an RV. The campground has a 50 amp socket for RVs.
In order to have power insider the car for air conditioning, charging phones and laptops, I ...
1
vote
1
answer
132
views
What is this wire-to-board connector?
For my project I want to use the circuit board of a SRAM Eagle AXS controller.
But I can’t figure out which kind of connectors they used for this. The male connector is 4 mm wide.
Maybe someone has ...
1
vote
2
answers
90
views
Old car patrol light
One of my friends has a car patrol light. He wants to use a transformer to supply power. This light has two lightbulbs, 50 watts each. The front light is red and stays on, on the opposite side is an ...
2
votes
2
answers
294
views
Transformer that doesn't take power when not used
With Is this (working) 2-doorbell system dangerous? and Why is it impossible to connect these two doorbells in series or parallel?, I arrived to the conclusion I need a new 220 V AC => 10 V AC ...
1
vote
1
answer
80
views
Alternative power source or bypass altogether? [duplicate]
I need to replace this 20+ year AC/AC 7.5VAC (4.0MM x 1.7MM FEMALE) adapter, but can not find it anywhere.
I'm looking for advice on what may work in its place, or if there's a way to bypass it ...
0
votes
0
answers
57
views
How to extend USB-C cable (USB 3)
It's look like this question is simple, but it's not at all.
See here what I did.
I have MacBook Air M1 base model, and I have lack of capacity, it's only 256, so I thought I need more space
So I ...
2
votes
4
answers
121
views
PCB Mount Switch to Breadboard Adapter
I'm currently working on implementing this switch in my project (PCB Mounted).
I'd like to move to the part of my project where I can implement a looks-like, works-like prototype, but I'm currently ...
0
votes
2
answers
88
views
I need an adapter for a 9-circuit/2-row dual USB computer cable from 0.1" to 2 mm pitch [closed]
Consider the (female) connectors in following photo:
On the left hand is a (sort of) typical PC case power switch connector (the braided cable goes to the actual switch. On the right hand is another ...
0
votes
2
answers
379
views
Why is the power adapter external (not built in) to the monitor? [closed]
I am considering to tape this dangling box to the back of my PC monitor for easier manipulation - I carry the screen up and down every day.
However, my intuition has raised a red flag. Perhaps there ...
1
vote
1
answer
59
views
Adapter sockets for different TO can pin circle diameters
I need to mount a laser diode from Ushio with 2.0 mm pin circle diameter,
onto a combined strain relief/ESD protection cable from Thorlabs, which has a socket with 2.54 mm pin circle diameter,
Are ...
0
votes
1
answer
86
views
What is the protocol that is being used in this Bluetooth dual SIM adapter that transfers voice and SMS? [closed]
I saw this product randomly on YouTube, and I'm really curious about the protocol it uses to communicate with the phone and how the phone can detect SIM cards. It uses Bluetooth for communication. For ...
0
votes
1
answer
49
views
How can the voltage of the original battery differ so much from the voltage of the original adapter?
It's about Xiaomi Mi Notebook Pro 15.6" 2019 JYU4148CN.
The original battery has a voltage of 7.6V and a current of 7.9Ah, the total Capacity is 60,040 mWh.
The original adapter has a voltage of ...
1
vote
1
answer
63
views
How are Mac AC adapters compatible when they are different voltages?
I recently had my Mac AC adapter die on me, so I just cut the end off and soldered it on to an old Lenovo AC adapter I had laying around. Since they are both 20V AC adapters, it works fine, but I am ...
0
votes
1
answer
75
views
What fire tests are done on power adapters/chargers?
I was curious about the fire risks in using a typical AC-to-DC wall adapter
(e.g., this)
and went to the UL website
to learn what exact tests were done to get the "UL LISTED" stamp,
but I ...
1
vote
1
answer
851
views
Replacing 4pin USB with USB-C works only in one direction
I have an AR1100 with a usb mini-B female connector :
https://github.com/adafruit/Adafruit-AR1100-Resistive-Touch-Controller-PCB
Basically 4 usual USB pins : GND, D+, D-, +5V
I want to replace it with ...
3
votes
2
answers
144
views
Adapter Power draw
On the adapter it says Input ~230V 1.5A, Output 29V 1.5 A.
If the adapter draws 1.5 A at 230 V and transfers them at 29V wouldn't that mean a power consumption of (230-29)V *1.5A = 301.5W in the ...
0
votes
0
answers
58
views
Measuring voltage across one end of a 50 ohm bias T and the other end is 50 ohm terminated
I was looking to measure the output voltage from one of the PCBs using a multimeter. I connected the center of the 50 ohm T adapter to the DMM, one end of the T adapter to the output port of the DUT i....
1
vote
1
answer
84
views
Sourcing a through-hole T-Connector male/female part for children's ride-on toy
I am having difficulty finding the through hole version of these "T-Connectors" as I've been able to identify from blog posts.
The type of adapter used can be seen in this image below and it ...
0
votes
1
answer
74
views
What is the polarity of a custom power supply? [closed]
I have a custom power adapter (this one), but I do not understand what the correct polarity is, as its tip can be reversed. In the picture I have highlighted the marks in the current situation (so the ...
4
votes
2
answers
391
views
What are DIP component carriers used for?
I was looking for SOP16 to DIP16 adapters, and I came across this Connector DIP Adapter Header 16 Position 2.54mm Solder Straight Through Hole.
What is it and what does it adapt between?
1
vote
1
answer
846
views
Should I use a ferrite core on my AC adapter? [closed]
I'm using an AC adapter for a port replicator (it meets the voltage and provides more amps) which doesn't have the ferrite core the original one had. Should I put one of these ferrite cores on it or ...
0
votes
1
answer
112
views
Socket or Surface Mount Adapter? (SOP16 to DIP16)
I'm looking to use a HX711 chip (which says it's a SOP-16L package,) and attach it to a circuit on a breadboard.
I've found two ways to do so: a socket or just the adapter.
Is there any difference ...
0
votes
2
answers
163
views
Adapter for a function generator output
I want to order this adapter, but I can't find it on the web. Can anyone please confirm the exact name of this adapter for a function generator having a channel output and terminals for a DC power ...
0
votes
0
answers
50
views
Surge protector + mains power adapter safe?
I was looking for a surge protected power strip/extension lead that could be mounted, have 6 or more outlets and came with a 5 meter mains cable with Type G (British plug) inlets and outlets. Having ...
0
votes
2
answers
1k
views
5.5x2.1mm Female Connector on 5.5x2.5mm Male Tip
Recently I lost my LG-27GP850 monitor power adapter which was 65w (19v, 3.42a). I could not find same tip size & watts power adapter. That's why decided to use other companies original adapter but ...
2
votes
1
answer
153
views
What is the name of this battery connector?
What is the name of this battery connector?
This is the link to the battery itself.
0
votes
1
answer
130
views
Inverter output to power laptop
I would like to gather info on power requirements for an electric system for a caravan, but I struggle with basic understanding.
My laptop needs to run off the 12 V battery, but the laptop charger has ...
1
vote
2
answers
46
views
Driving a DVI monitor from a monochrome source
I have a plasma display EL8358MS that is defective (burnt out.) The display has a signal convertor with these inputs:
...
0
votes
0
answers
119
views
Using a DMF5001NY-LY LCD with a Raspberry Pi Pico W
I just got myself a Raspberry Pi Pico to learn electronics and MicroPython. I was digging in my pile of "I bought this to do something one day with it, but never did" and found an old ...
2
votes
1
answer
775
views
How to loosen DC barrel jack to fit with 12 V adapter?
I have a DC jack such as this:
The lot that I bought are all too tight to fit a 12 V Adapter plug into them. Plug:
How do I loosen the jack? Are they always stiff when new? Should I buy new ones? ...
1
vote
1
answer
100
views
Battery replacement for 16 VAC
I have a mains power adapter that powers a small model train set. I would like the option to power this off a rechargeable battery, although I'm not sure this is possible, as it uses AC.
My current ...