Questions tagged [ac-motor]
For questions about electric motors driven by alternating current (AC).
75
questions
0
votes
2
answers
101
views
Is it possible to use just two SPDT relays to control this AC motor?
I purchased an inexpensive electric hoist off Amazon with the intention of partially replacing its control circuits so that it can controlled via ESPhome.
There are only 2 buttons on the control box. ...
0
votes
0
answers
36
views
AC Motor Control with TRIAC
I want to drive an AC motor using a TRIAC. I am new to this topic. I built this circuit and found that it is not working. What could be the reasons for this?
0
votes
0
answers
59
views
What parameters give unlinear torque model of induction motor?
I want to realize factors which give nonlinear model of torque toward speed with power consumption in induction motor.
I tried find math model induction motor. But usually, I had same charts:
As we ...
0
votes
0
answers
35
views
Can I run a one-phase AC capacitor motor from a three-phase VFD?
I'm building an art installation and found a cheap but strong AC Motor with capacitor. So by my understanding it is a one-phase capacitor run motor. The shield with the specs is very old and hardly ...
0
votes
0
answers
18
views
Impact of Low Power Factor on Loss Generation in PMSMs
I am focusing on the losses generation in PMSMs and still have some doubts about the role of a low power factor.
For the analysis, I consider a three-phase PMSM controlled with Field Oriented Control (...
0
votes
0
answers
41
views
Wiring AC 5 Wire Motor with 4 Phases to Run at Max
I'm trying to hardwire a fan motor to always run on max. Currently, it has a circuit board that allows you to adjust the speeds and requires a bit of fiddling to turn on and set the speed when the fan ...
13
votes
3
answers
2k
views
Why does a motor or ceiling fan exhibits low torque after capacitor-to-inductor swap?
For quite some time, I have been curious about what would happen if I replaced the capacitor in my ceiling fan with an inductor. Here in India, we usually deal with a mains voltage of about 220 - ...
0
votes
0
answers
48
views
Variable speed drive for an alternating current motor with PIC18F4431
I'm designing a control board for a three-phase motor speed controller using a PIC18F4431. I've used an inverter powered by 24V DC to convert the voltage to 24V AC to power the motor. Additionally, I'...
0
votes
0
answers
34
views
TRIAC Controlled Motor circuit: PWM logic doubt
I'm working on the logic board of my kitchen air extractor. I wanted to "hijack" the controls (physical buttons) to be able to control those with an ESP8266. While I was analyzing the ...
0
votes
0
answers
52
views
Why is there no torque in electric motors when the Iq current is zero and Id current is not zero?
Random vector position of stator current ( Id + Iq = Is ):
Now I draw the stator current/flux vector as shown below where “Iq = 0” and “Id ≠ 0”:
From lecture I’ve learned that the south pole of the ...
0
votes
2
answers
232
views
Using tunnel diode to cancel out armature resistance
Can we use tunnel diodes to cancel out armature resistance?
A tunnel diode when it is in its negative differential region under DC shifted AC(AC with some DC offset) and if the Vp-p of the AC is very ...
1
vote
1
answer
100
views
Slowing down a synchronous AC motor
I'd like to slow down the little AC motor, which drives the mechanical controls on my washing machine (yes it's ancient but it works just fine). The wash cycle is a bit short, and I'd like to make it ...
1
vote
0
answers
50
views
Identifying old capacitor
I need help identifying the capacitor that needs to be replaced. The capacitor was located in the motor of the sewing machine. It is not clear in the pictures, but it says:
.01 + .0005 x 2 and 600WV....
1
vote
0
answers
66
views
How can 120V fail to spin an AC motor that spins fine with 120V on a different power source?
While troubleshooting a home appliance, I found something odd: a 120V AC refrigerator fan stopped spinning despite being connected to 120V AC voltage (verified with my multimeter) inside the ...
1
vote
1
answer
69
views
Why does my food mixer have voltage across input cable leads even when unplugged?
I have a technical problem where the cable of a food mixer has voltage across its cable when unplugged. When I measure it with a multimeter at various times after being unplugged it shows a voltage ...