Questions tagged [ac-dc]
Questions regarding the safe and effecient design and implementation of AC voltage to DC voltage supplies. Typically Mains to some lower DC voltage.
443
questions
1
vote
1
answer
53
views
UL ratings and power supplies (DC transformer)
I read somewhere that if you sell a product that you plan to be UL certified, this means its power supply must be UL certified as well.
This means that if you supply power via a transformer (external ...
0
votes
2
answers
101
views
ATX Computer Power Supply Spark in Non-computer Application [closed]
I would like to ask for your assistance with using a Silverstone DA1650 Gold computer power supply (you can find more about it here: Silverstone DA1650 Gold) for a non-computer application. In this ...
0
votes
1
answer
63
views
Safely run a pump using the driver/controller built into an air conditioner - switch EMC motor for a pump motor
I am attempting to switch an ultra-efficient household air conditioner from air cooled to liquid cooled. The unit, (LG DUALCOOL with Watt Control-Eco - T06EV4), was attractive because it has 3 power ...
0
votes
0
answers
80
views
AC adapter interfering with WS2812B LED strip
I have 2 power adaptors connected on same AC line, both grounded.
Power adapter 1:
12V DC 10 A for powering 12 V LED strips, controlled by ESP8266, IRLZ44N MOSFET used to control brightness of the LED ...
6
votes
2
answers
1k
views
Is an AC/DC converter with no visible fuse before the transformer inherently dangerous?
I've been using a generic, unregulated mains AC/DC converter (wall-wart) for a very low-power project. It's output was a bit prone to 50 Hz ripple, so I opened it up to investigate how the circuit ...
0
votes
1
answer
81
views
DC appliances running on AC system [duplicate]
How do DC ran appliances work in an AC electrical system? For example, a house runs on AC, but the microwave runs on DC. How exactly is AC converted to DC? Does that DC power then have to invert back ...
0
votes
1
answer
282
views
Is there any benefit to converting from single to 3 phase AC before a DC conversion?
Compared to single phase, 3 phase AC produces less ripple in the resulting DC waveform when rectified. At the capacitor filtering stage, it is much cleaner with less sag than filtered DC converted ...
2
votes
3
answers
164
views
Trying to fix a mess with DC Power supply
I am not even close to know what I am doing with the electricity, but I have a power supply of my 8 cameras that is gone bad and I think I can manage to replace it myself, but there is a big BUT here. ...
0
votes
2
answers
119
views
Should consumer electronics have low voltage isolation?
I am making a MCU (PIC12) controlled 230V relay system. They will be operated from 230V mains. Should I use isolation (1:1 transformer?). I would use this converter for 230VAC-5VDC (or something like ...
-1
votes
1
answer
154
views
AC-DC Schematic - Is this a Death Capacitor [closed]
Is this a death cap? I think it's not a death cap because it doesn't connect to the DC ground, but I'm not 100% sure.
Image Source: Hi-Link HLK-20M24 Datasheet - https://www.rhydolabz.com/documents/...
0
votes
2
answers
625
views
Why aren't I getting a voltage reading from my AC/DC power adapter
I am new to electrical engineering.
I cut the barrel jack off the end of a 24V DC power adapter, exposing a red and white wire. I'm trying to determine the polarity of the red and white wires with a ...
2
votes
2
answers
69
views
Non Fused AC Rated Disconnect Switche for DC System
I have 110VDC supplied by a controller to power a actuator/motor located in a hazardous C1D1 environment. I wish to install a disconnect downstream of the controller in the hazardous location so the ...
4
votes
4
answers
1k
views
Predicting health of power supplies
I have a couple of 12 V, 1200 mA wall mount power supplies.
Currently, using a digital multi-meter, I am able to measure good voltage and amps coming out of some power supplies.
Since these are ...
-1
votes
2
answers
226
views
Why do photodiode transimpedance amplifiers care about signal frequency?
I'm designing a circuit to amplify low light levels (in the range of 0.1 uW) of measured black body radiation for application in a pyrometer. I don't have much experience with this kind of stuff so I'...
0
votes
1
answer
75
views
What fire tests are done on power adapters/chargers?
I was curious about the fire risks in using a typical AC-to-DC wall adapter
(e.g., this)
and went to the UL website
to learn what exact tests were done to get the "UL LISTED" stamp,
but I ...