Questions tagged [maximum-ratings]
Questions related to the maximum ratings of a component such as maximum voltage, heat and other specs which if exceeded will likely destroy the device
285
questions
1
vote
1
answer
41
views
ESD protection device selection
I want to select a ESD protection IC for my circuit with the following conditions:
Battery based and ultra-low-power
Battery voltage 3.6 V
My sensitive chips inside my circuit has Absolute Maximum ...
4
votes
2
answers
2k
views
Why does a battery have a limit for current in amperes?
I recently learnt that the voltage of the battery (for example, a 9V battery) is constant at their bounds, whereas the battery current depends on the load that is connected to it.
If I connect a 12V ...
0
votes
0
answers
38
views
Difference between Vid and Vidr
I have two different operational amplifiers datasheets with absolute maximum ratings. The TI LM358DR has a differential input voltage specification (Vid) of -32 V to 32 V, whereas the OnSemi LM358DR2G ...
0
votes
1
answer
90
views
For a CMOS closed-loop op amp, under what condition will the output influence the saturation condition of transistors inside the amplifier?
This question is from Example 9.6 of Razavi's book. Design of CMOS analog integrated circuits.
I will first outline my confusion regarding Razavi's solution and the clarification of the inequality ...
1
vote
1
answer
37
views
Board-To-Board Connector : Shield Pins : Voltage Bus?
Question
On a board-to-board connector, can the shield pins be used as power pins to carry bus voltage, or should shield pins always be tied to return?
Specific Connector
In my specific case, the ...
2
votes
4
answers
80
views
Resistor power rating in an AC circuit
Looking at this question and answer:
Source: Practical Electronics for Inventors, Page 91, Example 5
Shouldn't we use the peak voltage instead of the RMS voltage to calculate the minimum power rating?...
1
vote
2
answers
68
views
Cable current rating for high frequency applications
I am looking for power cables for high-speed motors, with frequencies up to 700Hz. All the tables that I find online are referred to 50/60Hz applications. I am not able to find derating factors ...
0
votes
3
answers
52
views
How do I test a MOSFET/IGBT for its maximum current and maximum voltage mentioned in the datasheet practically?
I am using an IGBT from Infineon (IGW25N120H3FKSA1). The datasheet mentions that the absolute maximum ratings for the IGBT are Vce(max) = 1200 V and Ic(max) = 25-50 A (depending on temperature). How ...
1
vote
1
answer
55
views
Undercurrent E-stop [closed]
what would be the effects of an emergency stop button rated significantly lower than the system's current draw?
Say for example, an e-stop rated for 10A DC in a system pulling 20A DC. Would the e-stop ...
1
vote
2
answers
56
views
Maximum Voltage Input and output current for transistor pnp and npn
How can I know the maximum voltage input for transistor. I look at datasheet. But confusing me little bit. Which is for maximum voltage. Afraid that might burn the transistor. Btw, my input circuit is ...
1
vote
1
answer
125
views
How is the boundary of input CM level calculated?
I will briefly state my understanding of the following equation, and then pose three questions at the end.
Equation (1) (2) refers to the circuit in the first picture, Equation (3)(4)(5) refers to the ...
0
votes
2
answers
79
views
For a MOS transistor, why is the maximum voltage of it be \$V_{dd}-V_{ov}\$?
Razavi stated that
the maximum output swing at X or Y is equal to \$V_{DD}−(V_{GS}−V_{TH})\$
as shown in the following picture, the second picture is the Fig.4.3
I don't understand why the equation ...
2
votes
2
answers
638
views
Can a 2N7000 transistor withstand 4.7-5 V gate voltage?
Here is the datasheet of the 2N7000 transistor. I need to use it in a circuit where an Arduino will provide the gate terminal with 4.7-5 V and the transistor needs to withstand 200 mA current.
It ...
0
votes
1
answer
62
views
Is it okay to replace a 127 V indicator LED with a 110 V one? (Both are AC)
The available LEDs have no famous brand so they don't have a specific datasheet where you can search and look-up online. So I need a general answer to my question based on the "most common" ...
1
vote
1
answer
172
views
Determining the maximum input power of a photosensor for a given laser power input
I need to measure the average power of a 1550nm pulsed laser output using a photodiode. The datasheet of the Thorlabs FDG03 photodiode can be found here (or if these links fail, the product page with ...