Questions tagged [transmitter]
A device used to turn an input into a signal that is then sent to a receiver.
48
questions
5
votes
1
answer
109
views
First radio transmitter. Taranis X-Lite, X9 Lite or Jumper T8GS?
I'm looking for a nice budget radio transmitter to start in the hooby and stay with it for some good time. I'm found these three good options but I'm tottaly newbie so I don't know the pros and cons ...
5
votes
1
answer
1k
views
Taranis X9D Plus 2019: Switches SE,SF,SG,SH, and SI are not working/responding on Betaflight
So switches SA,SB,SC, and SD work on Betaflight. Aux channels 1 through 4.
But switches SE,SF,SG,SH, and SI are not working/responding on Betaflight. Aux channel 5 through 9, I believe
I am using TBS ...
3
votes
1
answer
469
views
In what direction should I orient the dipole antenna on my 2.4 GHz RC transmitter?
My RC transmitter has a movable antenna that allows me to change its orientation, like this one:
In what direction should I point my 2.4 GHz RC transmitter antenna for best range and signal ...
4
votes
2
answers
3k
views
Why is 900 MHz better for long range than 2.4 GHz?
There are various transmitter modules like the FrSky R9M system which operate at around 900MHz rather than the more commonly seen 2.4GHz. Why is 900MHz better for long range drones, and why is 2.4GHz ...
4
votes
1
answer
81
views
Analog Graupner MC-12 with R-700 receiver
I have an old Graupner 35Mhz transmitter and receiver which I would like to get running again. Bought batteries and connected power and a servo to the receiver but nothing happens when I use the ...
11
votes
2
answers
5k
views
Can circularly and linearly polarized antennae be used together for FPV?
I have a few spare antennae of mixed polarizations I'd like to be able to reuse for my FPV gear.
Is there anything I need to know about incompatible configurations of mismatched polarizations ...
4
votes
3
answers
4k
views
Why is 5.8ghz used for FPV and 2.4ghz use for transmitters?
Why do most VTXs use 5.8ghz and most transmitters use 2.4ghz?
2
votes
2
answers
3k
views
How do I set up the RSSI readout on an XM+ receiver channel?
I have an old XM+ receiver that does not do RSSI. Some of the newer ones come with RSSI set up on a channel. How can I set up RSSI to be on a certain channel?
4
votes
2
answers
6k
views
How are Hall effect gimbals different than standard gimbals?
I know that hall effect gimbals are supposed to be better than standard gimbals and are seen on a lot of expensive transmitters. What are the differences between a Hall effect gimbal and a standard ...
3
votes
4
answers
3k
views
Drone “fine tuning”
On my controller for my drone there are 4 buttons:
Forward fine-tuning
Left fine-tuning
Back fine-tuning
Right fine-tuning
What is “fine-tuning” and how does one decide what direction to “fine-tune” ...
6
votes
2
answers
779
views
What is the background of remote controller modules?
I've seen that in many remote controllers you can plug in an external module under it.
Are there other purposes for these modules than just being transceivers?
Are the module bays offered by multiple ...
6
votes
3
answers
2k
views
USB Webcam Parts for FPV?
I have a camera taken out of an old usb webcam. It has four wires attached to and labeled on the board: 5V (red); DM (white); DP (green); and GND (black). I was thinking I could use it just like a '...
3
votes
2
answers
1k
views
How do I set up LUA scripts on my OpenTX radio?
I’m looking at how to use LUA scripts and was wondering how to configure them I am OpenTX radio.
Thanks.
More info: at present, I don’t want to write my own scripts, only run scripts that I can find ...
4
votes
1
answer
54
views
Kk2.1.6 falling in mid air and losing control
I am recently flying my DIY quadcopter built with lightweight aluminum bars and a kk2.1.6.
It was a very good experience until it suddenly started losing control and it fell midair. It tried to gain ...
5
votes
4
answers
442
views
r-xsr won't bind to qx7s
I'm trying to bind an r-xsr to a qx7s, but the receiver shows a solid red, green and blue light and won't bind.
I have updated the receiver to version 2.1.0 LBT and the transmitter to the EU version ...