All Questions
Tagged with transmitter receiver
16
questions
0
votes
0
answers
5
views
How do I add camera live streaming on my transmitter from the camera on the plane?
I'm a newbie in RC Airplanes and have bought the AL37 Airliner and installed everything right. What I didn't know was how do I add a camera to the plane which gives a live streaming view to the ...
1
vote
1
answer
17
views
I have Radiomaster Boxer CC2500. Can i add an external elrs module on my Tx to make it elrs compatible or do i need to buy a new Tx?
I bought a CC2500 version of Tx which is sightly outdated. I didn't know this while buying. I came to know that i can use FrSky rx to make my drone compatible with my tx. If i want to make my tx ELRS ...
2
votes
1
answer
90
views
Receiver and transmitter issue
I am trying to build a drone from scratch. I purchased Fly Sky FS-CT6B 6 transmitter. but unfortunately the receiver is not supporting PPM communication. I am using pixhawk 2.4 as flight controller.
I ...
2
votes
1
answer
35
views
Drone drifts to same direction even after leaving stick
I have micro fpv racing drone with jhemcu f4 noxe v3 flight controller. Drone works fine with all functions. But when I try to move drone to any one direction and leaves stick, drone continues moving ...
4
votes
1
answer
929
views
Can't disable SAFE or change SAFE mode
I was gifted one of these (with souped-up motor and ESC) and was delighted when I discovered it could be bound to my Spektrum DXS transmitter. However, the receiver is stuck in beginner mode. I've ...
4
votes
1
answer
179
views
Brushless Motor/ESC Voltage Cut-off
I got an ESC and brushless motor set for my RC car. After I finally got it to work, I put my car back together, but then when I turn on the transmitter and then the ESC, the motor emits a "beep&...
5
votes
2
answers
143
views
Brushless Upgrade for RC Car
I was told that if my question was about motors and ESCs than it would be okay to put it on here even though it has to do with an RC car...
I am wanting to do a brushless upgrade for my WLTOYS 12428 ...
5
votes
1
answer
574
views
XM+ bound to FRSKY x9 lite, but commands not showing up in betaflight
I'm very new to making drones, so sorry in advance for lack of proper terminology or if this is a dumb question. I've bound my xm+ to my transmitter (solid green light showing on receiver), but for ...
5
votes
1
answer
584
views
Binding DX5e (or any other hobby controller) to generic "toy" drone - protocol compatability
I picked up a really cheap generic drone mostly for the purpose of tinkering and testing with something that I wouldn't mind losing or destroying. However I can't seem to bind to it with any of my ...
5
votes
3
answers
2k
views
Is it feasible to use an RC car transmitter/receiver to control an RC plane?
I am a beginner to the hobby and I've been constructing chuck gliders out of foam board and card for a few years. I'd like to start making models that I can control, but I don't have much of a budget. ...
4
votes
1
answer
114
views
How do I test if my DX5e antenna is still good?
I have a second hand DX5e tx that I haven't really used a ton yet, just on a little Blade Inductrix, within my house. However, the upper plastic end is broken off and the actual antenna seems pretty ...
5
votes
1
answer
1k
views
Taranis X9D Plus 2019: Switches SE,SF,SG,SH, and SI are not working/responding on Betaflight
So switches SA,SB,SC, and SD work on Betaflight. Aux channels 1 through 4.
But switches SE,SF,SG,SH, and SI are not working/responding on Betaflight. Aux channel 5 through 9, I believe
I am using TBS ...
4
votes
1
answer
81
views
Analog Graupner MC-12 with R-700 receiver
I have an old Graupner 35Mhz transmitter and receiver which I would like to get running again. Bought batteries and connected power and a servo to the receiver but nothing happens when I use the ...
11
votes
2
answers
5k
views
Can circularly and linearly polarized antennae be used together for FPV?
I have a few spare antennae of mixed polarizations I'd like to be able to reuse for my FPV gear.
Is there anything I need to know about incompatible configurations of mismatched polarizations ...
2
votes
2
answers
3k
views
How do I set up the RSSI readout on an XM+ receiver channel?
I have an old XM+ receiver that does not do RSSI. Some of the newer ones come with RSSI set up on a channel. How can I set up RSSI to be on a certain channel?