Questions tagged [receiver]
An electronic component that receives the information sent by a transmitter.
45
questions
2
votes
1
answer
69
views
Trying to bind xm+ to tx12 radiomaster
Hello I am trying to bind xm+ to a radiomaster tx12 w cc2500 mode inside ive tried rolling back the firmware on the xm+ but to no prevail. Also tied version 2 with frsky x2 (d16) Nothing seems to be ...
0
votes
1
answer
99
views
How to check whether receiver is damaged?
I am a beginner. I have bought RadioMaster TX12 and turned it on without an antenna and with an extra module for 915mhz for 1 minute. Internal RF was not off. How can I check whether something got ...
2
votes
1
answer
87
views
Receiver and transmitter issue
I am trying to build a drone from scratch. I purchased Fly Sky FS-CT6B 6 transmitter. but unfortunately the receiver is not supporting PPM communication. I am using pixhawk 2.4 as flight controller.
I ...
2
votes
1
answer
452
views
Raspberry pi controlled drone: using raspberry pi as a receiver
I build a drone very similar to the Rotor Riot Cinewhoop, I want to use a Raspberry Pi zero to make the drone fly autonomously.
I think that the best idea is to use the Raspberry Pi as a receiver, and ...
0
votes
1
answer
104
views
Can we use two radio receivers on drone with different frequencies to increase range possibilities and safety?
I think about installing additional 915MHz receiver into drone which has 2.4GHz receiver. I want to keep controls when 2.4GHz is jammed or drone flied too far (or behind large obstacle).
But opposite ...
2
votes
1
answer
35
views
Drone drifts to same direction even after leaving stick
I have micro fpv racing drone with jhemcu f4 noxe v3 flight controller. Drone works fine with all functions. But when I try to move drone to any one direction and leaves stick, drone continues moving ...
1
vote
1
answer
555
views
How to connect TBS Crossfire nano rx to Matek F405-WMN?
How to connect crossfire nano rx to FC Matek F405-WMN? I don't see commands receiver connection on the wiring diagram http://www.mateksys.com/?portfolio=f405-wmn#tab-id-4
Is it possible to connect two ...
0
votes
1
answer
50
views
Problems with drone receiver using BetaFlight
I got some problem when using Betaflight and trying receiver, I am not sure how to fix them😭. First, when I toggle the left stick, the throttler raise so quickly to the limit I set, how can I let it ...
4
votes
1
answer
663
views
What is this pad on the HappyModel EP2 2.4G ExpressLRS Receiver?
I have soldered wires to "HappyModel EP2 2.4G ExpressLRS Receiver".
There is one pad I don't know and can't find what it is for.
See the pic "EP2 RX connection diagram".
The ...
3
votes
1
answer
128
views
Help getting this flight controller to work with this receiever
I am working on building a drone. I have the DJI NAZA M LITE flight controller, and this receiver. The pinout for the battery and ESCS is pretty clear, but I'm not sure how I should go about ...
3
votes
1
answer
974
views
Motor doesn't work, ESC doesn't calibrate
After I figured out why SAFE never turned off, now I'm stuck because my motor won't spin and I can't enter calibration mode of the ESC. After turning on the plane, it does three startup beeps in ...
4
votes
1
answer
906
views
Can't disable SAFE or change SAFE mode
I was gifted one of these (with souped-up motor and ESC) and was delighted when I discovered it could be bound to my Spektrum DXS transmitter. However, the receiver is stuck in beginner mode. I've ...
4
votes
1
answer
166
views
Choosing ESCs for an Autonomous Drone
I'm about to build my first drone. I chose the PixHawk 4 with PX4 as a flight controller and the Raspberry Pi Model 3B as the companion computer.
I am not sure about the ESCs yet. So far I'm ...
4
votes
0
answers
105
views
Can I use an RX6R's PWM and SBus outputs simultaneously?
I'm looking at options to build a pan/tilt system for FPV. The FC that I have available has only 4 servo outputs, and the airplane has 3 servos. Given this, I can't run the pan and tilt through the FC....
3
votes
3
answers
875
views
Could using a 2.4GHz controller frequency interfere with an onboard computer trying to access 2.4GHz WiFi networks?
My situation is this:
I will be building a quadcopter drone (and later a hexcopter) that will most likely use 2.4GHz RC with a Pixhawk. I will also have a computer onboard (Raspberry Pi, either 4B or ...