Unanswered Questions
1,020 questions with no upvoted or accepted answers
11
votes
1
answer
144
views
Is gallium slippery at room temperature in an inert atmosphere?
Ice is slippery when it isn't too far below it's melting point because the surface molecules are less loosely bound than the bulk and form a thin liquid layer.
Pressure melting is a much smaller ...
- 224
10
votes
1
answer
328
views
Why are IUPAC's definitions of exo- and endothermic disconnected from the direction of heat flow?
I'm wondering if anyone can provide a rationale for IUPAC's definitions of exothermic and endothermic since they disconnect these terms from the direction of heat flow.
Specifically, here are IUPAC's ...
CommunityBot
- 1
8
votes
0
answers
392
views
What exactly is an "electron-sponge"?
What exactly an "electron-sponge" [behavior/action/property/system] nickname is, and what makes a material an "electron-sponge" (preferably, quantitatively)?
From what I found, it's typically a ...
- 38.4k
8
votes
0
answers
102
views
Removal of nickel plating on MgB2 without damaging the boride?
I need to remove a nickel plating of a MgB2 wire without causing damage to the MgB2. I felt that electrolysis is the best method but I do not know what electrolyte to use for this. I also need to coat ...
CommunityBot
- 1
7
votes
0
answers
183
views
Why does entropy increase in reactions that make more molecules?
I used to understand this (more molecules ⇒ more degrees of freedom), but do no longer, because the total number of atoms is conserved, so translational d.o.f. should just be turned into internal d.o....
7
votes
0
answers
99
views
Why does diethylmethylamine have such a low melting point?
According to PubChem, diethylmethylamine has a remarkably low melting point of $-196.0\ \mathrm{^\circ C}$. This is substantially lower than the melting points of dimethylethylamine ($-140.0\ \mathrm{^...
CommunityBot
- 1
7
votes
0
answers
516
views
Does phosphoric acid remove stainless steel electropolished layer?
Electropolished stainless steel has a high corrosion resistance due to the oxide film that is created during electropolishing. The film mainly consist of chromium(III) oxide.
Phosphoric acid is ...
- 815
6
votes
0
answers
171
views
Which xylenes, if any, are immiscible with DMSO?
"Xylene" is reported to be immiscible with dimethyl sulfoxide (DMSO), according to a few solvent miscibility tables found online (chart 1, chart 2, chart 3). I have tried to locate some ...
- 782
6
votes
0
answers
82
views
Do "pseudo Van der Waals" gases exist?
In college, when deriving the Langmuir isotherm for gas-solid adsorption, the professor proposed a modified version of the Van der Waals state equation, what he called the "pseudo Van der Waals ...
- 4,826
6
votes
0
answers
135
views
Correct Definition of Absolute Electrode Potential
I thought absolute electrode potential is Galvani potential difference at the interface. However, it is given by following equation in John Bockris - Modern Electrochemistry (Ref.1): $$ E^M \mathrm{(...
- 865
6
votes
0
answers
206
views
Why is the reverse aldol cleavage of fructose 1,6-bisphosphate highly endergonic under standard conditions?
I have another question similar to this one. I just don't have intuition for why reactions are thermodynamically favorable or unfavorable and I'd like to build it. This time I'd like to ask about ...
CommunityBot
- 1
6
votes
1
answer
197
views
Understanding elementary rate laws from a probability stand point
I am learning about chemical kinetics and dynamics and as I understand for a general chemical reaction
$$\ce{aA + bB -> cC + dD} $$ whose reaction rate, r, can be described by an elementary rate ...
CommunityBot
- 1
6
votes
0
answers
614
views
Thermophysical properties of liquid Galden LS 230 between 25 °C and 230 °C
I'm looking for thermophysical properties of Galden LS 230, a liquid polymer (PFPE) produced by Solvay (https://www.solvay.com/en/markets-and-products/featured-products/Galden.html) at temperatures ...
CommunityBot
- 1
6
votes
0
answers
207
views
I found transition states (TS), but calculations aren't supported by experiment. Do I look for more TSs or somewhere else?
I'm using Gaussian to investigate a catalyst system.
Experimental evidence showed that one of three analogues (R = phenyl, Ph), yielded a benzosultam
when treated with 2,4,6-...
- 44.1k
6
votes
0
answers
143
views
Seeking titanium compound, melting point <1600 °C, decomposes to TiO
The title says it all. I’m new to glass making, and I need a titanium compound that will render me $\ce{TiO}$ through decomposition, and has a melting point under 1600 °C. Hopefully I can get one ...
CommunityBot
- 1