Unanswered Questions
63 questions with no upvoted or accepted answers
6
votes
0
answers
105
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
- 13.9k
4
votes
1
answer
113
views
Samox crankset okay for touring bike?
I just bought a new Salsa Marrakesh. My main use is moderate distance touring (1000 km to 7000 km tours) although it might end up going further.
The Salsa web-page says that the bike has an Alivio FC-...
- 20k
2
votes
0
answers
34
views
Square taper with 15.5mm end?
I got a Star Trac NXT for £15 for some indoor fitness but it's missing its left crank arm. I thought to myself oh I'll just throw on a standard steel crank arm and I'll be good to go BUT it doesn't ...
- 5,202
2
votes
1
answer
72
views
Sram/Avid brake hose compatiblity
I have Sram Rival AXS which I want to transfer from one bike to another. Unfortunately the new bike is bigger (M -> XL) so new brake hose is required. SRAM recommends SRAM Brake Hose Kit - Double ...
CommunityBot
- 1
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
- 2,090
2
votes
0
answers
95
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
0
answers
284
views
after multiple brake bleed, lever's max stiffness is still close to bar
so after a few bleeds i've done on these Shimano saints, because of new levers replacement, i've found that the rear brake lever, although on max stiffness, goes way further to the bar then the other ...
- 185
2
votes
0
answers
175
views
SRAM Hydraulic brake stuck (with a changed bite point) after landing/impact
I experienced a weird problem on my SRAM level t 2 piston brakes.
I like hopping my bike around, e.g. bunny hopping onto curbs. Sometimes, if the impact is hard, the brake lever would have reduced ...
- 121
2
votes
0
answers
161
views
What kind of frame and brakes are these?
I just bought a bike and I can't figure out what kind of frame and brakes it has.
I found that the derailleurs were made by DNB Japan somewhere around 1960 and that the handlebar is french (Guidonn ...
- 128k
2
votes
0
answers
3k
views
Shimano Nexus 3 coaster brake screeching sound
When I brake hard/er with my Shimano Nexus 3 coaster brake it makes a loud screeching sound. Like really loud, everybody on the street would hear it and turn around. Since I know it's all internal all ...
- 352
2
votes
0
answers
706
views
Internal Roller Brake Problem
I have Shimano Inter M Roller Brakes on my bike. I felt the rear brakes were a bit light after riding 800 or so KM (total mileage on my bike so far) so I thought maybe theres a bit of cable stretch ...
- 115
2
votes
1
answer
63
views
Square-taper crank wobble/movement in only one spot
For square-taper aluminum cranks:
When my drive-side crank is in the 12:00/highest position and the non-drive side in the 6:00/lowest position, there is slight play between both cranks (it rotates ...
- 15
2
votes
1
answer
174
views
Front Mountain Bike Cable Disk Brake Is Too Snappy on First Pull
When I grab my front disk brake for the first time on a ride after my bike has sat for a while it will buck me forward. Once it bucks me it works great. I have tried cleaning it with disc brake ...
1
vote
1
answer
115
views
Bike pedaling makes cracking noise under middle or high load
Can this be related to bottom bracket bearings of Race Face BB92, PressFit? The chain is freshly lubricated and quite a new one. No noice is produced when pedalling with low load or not pedalling.
...
CommunityBot
- 1
1
vote
1
answer
505
views
Running DUB wide crank with 52mm chainline
I have a set of sram xx1 carbon cranks that are DUB wide. My bike (2023 Specialized Epic Evo) is DUB crank 52mm chainline. If I add BB spacers to the DUB wide crank and use a 6mm offset chainring ...
CommunityBot
- 1