Unanswered Questions
96 questions with no upvoted or accepted answers
6
votes
0
answers
109
views
What is forward drag on a coaster brake
I have a single-gear coaster brake bicycle that needed fixing. I would have to pedal real hard to get it to go and backpedal a block in advance for bike to stop. Very spongy brakes. Well I took brake ...
- 13.9k
4
votes
0
answers
279
views
Sram AXS derailleur does not shift
Have you encountered a problem where a rear AXS derailleur stops shifting? Any suggestions?
I bought a mint 2023 GX AXS derailleur on Marketplace, it worked for the first short test ride on a road but ...
- 141
4
votes
1
answer
123
views
Samox crankset okay for touring bike?
I just bought a new Salsa Marrakesh. My main use is moderate distance touring (1000 km to 7000 km tours) although it might end up going further.
The Salsa web-page says that the bike has an Alivio FC-...
- 20.1k
2
votes
0
answers
46
views
Why have my rim brakes started making a scraping noise?
I bought a bike about 7 months ago, and I've noticed over the last few weeks that it's started making an unpleasant scraping noise when I brake. Does anyone know what might be causing this and how to ...
- 121
2
votes
0
answers
34
views
Square taper with 15.5mm end?
I got a Star Trac NXT for £15 for some indoor fitness but it's missing its left crank arm. I thought to myself oh I'll just throw on a standard steel crank arm and I'll be good to go BUT it doesn't ...
- 5,202
2
votes
1
answer
74
views
Sram/Avid brake hose compatiblity
I have Sram Rival AXS which I want to transfer from one bike to another. Unfortunately the new bike is bigger (M -> XL) so new brake hose is required. SRAM recommends SRAM Brake Hose Kit - Double ...
CommunityBot
- 1
2
votes
0
answers
50
views
Something like chainsuck on RD lower pulley after new crankset install?
I just switched out a Shimano M5100 crankset for a SRAM GX Eagle crankset. I am using a KMC X11-EL chain. I cleaned the chain before installing it with the new crankset. My RD is a Shimano SLX 11-...
- 2,090
2
votes
0
answers
95
views
Cable housing end cap for BR-M375
I replaced the no name brake calipers on an entry-level ebike for Shimano BR-M375. The cable housing for the rear caliper was a bit too long, so I cut off a few centimeters. Then, I put a new 5 mm end ...
- 4,159
2
votes
1
answer
243
views
Upgrading Shimano Acera 8 speed Rear Derailleur to 8 speed Shimano XTR derailleur
Looking for some help here. I am upgrading Shimano Acera 8 speed rear derailleur to 8 speed Shimano XTR rear derailleur and it appears that because the old 8 speed XTR derailleur has a clip for the ...
CommunityBot
- 1
2
votes
0
answers
60
views
clicking chain on 3rd gear only
Shimano DI2 11 speed XTR on my gravel bike. The 3rd from smallest gear on the cassette makes a clicking sound. Any other gear its fine. Cassette and chain are fairly new. Have reindexed, checked ...
- 21
2
votes
0
answers
284
views
after multiple brake bleed, lever's max stiffness is still close to bar
so after a few bleeds i've done on these Shimano saints, because of new levers replacement, i've found that the rear brake lever, although on max stiffness, goes way further to the bar then the other ...
- 185
2
votes
0
answers
177
views
SRAM Hydraulic brake stuck (with a changed bite point) after landing/impact
I experienced a weird problem on my SRAM level t 2 piston brakes.
I like hopping my bike around, e.g. bunny hopping onto curbs. Sometimes, if the impact is hard, the brake lever would have reduced ...
- 121
2
votes
0
answers
416
views
Using 11-36t 9 speed derailleur with 11-40t 9 speed cassette
So I've got the shimano altus rd-m2000 and it says that it only supports 11-36t. However, I've seen people on forums say that it's possible with this derailleur. Even it I was wondering if with a ...
- 21
2
votes
0
answers
835
views
Why do SRAM rear derailleur not have a parallel movement
My SRAM rear derailleur (Rival 22 circa 2016) has a non parallel movement. When it is in the lowest gear, the cage and pulley sprockets align with the cassette sprockets, but when it's in the highest ...
2
votes
0
answers
161
views
What kind of frame and brakes are these?
I just bought a bike and I can't figure out what kind of frame and brakes it has.
I found that the derailleurs were made by DNB Japan somewhere around 1960 and that the handlebar is french (Guidonn ...
- 128k