Unanswered Questions
26 questions with no upvoted or accepted answers
4
votes
0
answers
59
views
How do I stop the extruder from sticking to the back corner of the part?
I was gifted a Creality Ender-3 and thus have begun my first foray into 3D printing. Things went well for the setup and first prints; I printed some of the 3D files that came with the printer, then ...
3
votes
0
answers
1k
views
The nozzle keeps clogging, midway through the print while printing with PETG filament
I've recently purchased Creality Ender 3 V2. When I print PLA, I face no issue at all but while printing PETG, the nozzle keeps clogging after the second or third layer. I even tried printing PETG by ...
3
votes
1
answer
1k
views
Creality Ender 6 Heating Failed
There is a message on my Ender 6 that is telling my that my heating failed. This happened last night in the middle of a print. I have cycled the power like the screen says but the nozzle does not heat ...
3
votes
0
answers
227
views
Silicone socks for nozzle only?
Is there a readily available silicone sock that goes just over the nozzle, to supplement an existing sock around the heat block body? I've seen a product for the E3D V6 that goes around the entire ...
2
votes
0
answers
229
views
Anycubic i3 Mega layers don't stick together/are too thin
My Anycubic i3 Mega suddenly stopped printing properly. As you can see on the images attached, the printed filament seems to be too thin which causes the layers to not stick together.
I already:
...
2
votes
0
answers
68
views
Path of a nozzle crosses over itself
I built my first printer couple of days ago. I started printing small models (20x20 mm max.) and everything was alright at first. However, when I tried to print a bit larger models, I started ...
1
vote
0
answers
76
views
Ender 3 nozzle temp turns off briefly at start of print
When I need to print higher-temp filament at 225 °C the nozzle temp turns off for just a second but this is enough to send the temp down to about 200 °C before it recovers to print temp. This jams up ...
1
vote
0
answers
301
views
How do I choose a nozzle for PA12+CF for Kobra Max?
I am sorry if I sound too newbie, but to me, it seems like an unsolvable riddle:
I have not yet used any other nozzle than the one that comes with my printer.
I would now like to print Fiberlogy Nylon ...
1
vote
0
answers
54
views
Speed bump like structural distortions in 3D printed samples
I am printing 5-152 mm(L)x35 mm(W)x3 mm(T) samples using a commercial PLA filament with 0.1 mm layer height (30 total layers). The raster width is 0.4 mm while the raster angle in all layers is 0/0°. ...
1
vote
1
answer
972
views
Z-Probe height isn't working
I just upgraded my CR-10 to a 32-bit board with Marlin and a BLTouch for bed-leveling.
Here is my process:
Run bed-leveling and save setting to EEPROM
Make sure that software end-stops are off with <...
1
vote
0
answers
24
views
Any method that I can refer to simulate 3D scanning and flow through extruder in MATLAB?
I would like to simulate the 3D scanning process with a specific wavelength and swath width of the beam, etc. and then reproduce the image, the whole of which in MATLAB. I also want to simulate the ...
1
vote
0
answers
86
views
What tolerance class does E3D uses for their metric thread nozzles?
As we know E3D nozzles use M6 threads. These are metric threads, so they've different tolerance classes but which tolerance class are they using?
1
vote
0
answers
549
views
Too long time to wait for M109 to stabilize when changing extruders
I would like to kindly ask for some advice.
I've got 2 extruders and 2 nozzles, they are working fine. I'm printing from Ultimaker Cura 4.1 generated files. I have problems with temperature ...
1
vote
0
answers
297
views
Creality CR10 S5; the Z dimension is wrong after switch from 0.4 to 0.2 mm nozzle
So I tried to print a model with a 2 mm thickness main area, and a couple 4 mm parts that stick out.
Instead the 4 mm is 3.05 mm and the 2 mm is 1.07 mm (0.042 inches ...
0
votes
0
answers
21
views
Repairing/cleaning nozzle assembly for Flashforge/Monoprice Printers
I have a Monoprice MP Voxel, which is a rebranded Flashforge Adventure 3. These printers have an easily removable nozzle assembly, also shared with the Flashforge Adventure 4. The assembly has the ...