Questions tagged [oak]
The oak tag has no usage guidance.
16
questions
0
votes
0
answers
153
views
What would cause wood filler to turn black when refinishing oak floor?
I was refinishing some old oak floors in rough condition, and troweled in Duraseal wood filler after a rough sand. Mostly, it worked fine, but in some places in one room, the filler turned dark or ...
6
votes
1
answer
3k
views
Can I hammer 25.4mm x 300mm oak dowels into a 25mm hole?
I bought the oak dowels supplied as 25mm x 300mm to fix through three oak sleepers total height 300mm.
I then bought a 25mm auger bit.
When I just checked the dowels with a calibrated digital caliper, ...
0
votes
0
answers
438
views
How to apply Rubio Monocoat and Black Bison Wax to white oak
I love the look of black bison wax on oak as a way to really bring out the grain. (see example photo)
Until now I've only used rubio monocoat as a finish. It's pretty much impossible to mess up and it ...
3
votes
0
answers
115
views
Supplied PAR white oak, one plank has woodworm holes
I'm a novice woodworker. Ordered £2000 worth of PAR white oak online. One 2m plank of 144x45 has worm holes at 30cm from the end. When ordering I specified I would be cutting to 1m lengths but on ...
3
votes
1
answer
1k
views
Advice for retouching old oak/maple furniture at home [finish losses]
I am reframing a question from before as my requirements have changed.
I have found a great old oak table and chair set which the neighbours wanted to get rid off. The table has a manufacturer label ...
0
votes
1
answer
529
views
Can I touch up old oak chairs and tables using Howard's Restor-A-Finish?
I have found a great old oak table and chair set which the neighbours wanted to get rid off. It is well used but in good condition. The photo below shows the wear and tear the set has had over years (...
3
votes
1
answer
1k
views
Making red oak look more like white oak
I am planning an open wood staircase for new home in white oak and the cost is getting out of hand. The plan is to stain some parts dark and other parts light.
I am wondering if I could use red oak ...
6
votes
2
answers
6k
views
Repair a crack on the side of an oak table
My oak table shows a split at the side of it. Is there a way I can address it?
What would you do?
I have plans of refinishing my oak table with a darker wood stain.
1
vote
2
answers
747
views
How to remove a 25mm drill bit stuck in oak sleeper
Whilst pinning three layers of oak sleepers together with oak dowels, I have managed to get the 25mm diameter auger drill bit stuck.
Is there any oil or lubricant that I can use to try and release the ...
1
vote
0
answers
37
views
OAK Colour too dark on refinished clear aqua-Varithane gloss, 2nd vs 1st floor mismatch
I have resurfaced my 2nd oak floor and removed all dust but a sample stays far too dark compared to the 1st oak floor.
It seems nothing will retain the pastel white oak shade on the 2nd floor as much ...
1
vote
1
answer
184
views
Oak edge-glued panel desk small cracks along the pores
I bought a 210×65×3.8 cm oak countertop and attached metal legs to it to make a desk. It was unfinished, so I sanded it and applied 3 coats of shellac to the top and edges (with a light sanding after ...
1
vote
3
answers
802
views
DIY "white wash" from thinning latex interior paint?
I'm looking to paint a red oak commission piece and the client asked about a "white wash" type finish instead of purely opaque white paint such that the grain shows through.
I was wondering if there ...
0
votes
2
answers
100
views
Painting deep grain in oak
I have some doors and millwork in white oak and have noticed that after we prime it, there are, here and there long thin crevices where the oak had some exceptionally deep grain and the oil-based ...
4
votes
1
answer
2k
views
Is Rubio Monocoat appropriate on red oak furniture?
I am making a bunk bed out of 8/4 red oak. It has very open grain/pores in some places and I'm concerned about my finish process.
I'm basing my design on plans from the Wood Whisperer. He finished ...
0
votes
2
answers
588
views
Fresh sawn oak sleepers deck
I'm planning to make a deck (~18m2) using oak railway half-sleepers (50mm thick, 200mm wide). They are fresh sawn, so they are pretty rough with splinters, etc. Is this a good idea at all? Can I sand ...