Skip to main content
Woodworking

Student

 Student
First question with score of 1 or more.
Awarded 2032 times.
Soft-close drawer guides won't retract without continuous pressure
Awarded Jul 14 at 0:35
Sap oozing from stripped pine doors - over 100 years old!
Awarded Jul 10 at 18:53
Can I put pocket-hole screws in the edge of board?
Awarded Jul 9 at 6:05
Hand saws not marked as rip or cross cut
Awarded Jul 7 at 14:41
What finish is this and how can I fix after bad coffee accident…?
Awarded Jul 6 at 16:48
What wood finishes stand up to machine washing
Awarded Jul 6 at 15:07
Raise one side of bench by 2mm
Awarded Jun 28 at 7:17
Need Some Advice on Cutting Cork
Awarded Jun 22 at 13:42
Can I thin over-thickened boiled linseed oil with unboiled linseed oil?
Awarded Jun 21 at 12:52
Preparing lumber by splitting verses cutting
Awarded Jun 16 at 12:02
Enclosing an MDF sheet in 4x4 Cedar
Awarded Jun 3 at 17:35
Identifying Period Molding In-Situ
Awarded May 11 at 8:50
Should I use a partially or fully threaded screw?
Awarded May 8 at 19:17
Cheap Surfacing Bit and Quality Carbide Cutters
Awarded May 8 at 9:26
I have a 200 lbs metal plate that was screwed in a wood board with 5 screws (1/4" diameter, 3" long). I had to remove the screws
Awarded May 3 at 7:18
Chalk method for planing?
Awarded May 3 at 7:05
Joining long stair treads
Awarded May 3 at 7:01
Need help identifying japanese chisels
Awarded Apr 18 at 8:03
How can I lighten a new white oak floor repair that has 1st coat poly to match current yellowed white oak floor (18 years old)?
Awarded Apr 11 at 13:19
re-finishing only a limited area of a guitar body
Awarded Apr 5 at 8:19
How to cut a straight 10cm section out of a 20cm post
Awarded Mar 30 at 13:34
how to get a really nice finish on wood as a beginner?
Awarded Mar 27 at 18:57
Drywall mud to patch bubbled veneer?
Awarded Mar 27 at 7:48
What is the name of the brace?
Awarded Mar 26 at 7:57
Getting rough results when cutting parallel to the side
Awarded Mar 25 at 8:50
Can I get two parallel sides of a board with only a jointer?
Awarded Mar 22 at 3:09
How to use a very large Forstner-style bit
Awarded Mar 20 at 8:50
Joining cross supports to workbench legs
Awarded Mar 14 at 12:49
Making a thick door not catch on a drawer front
Awarded Mar 13 at 7:57
Steam Bending American Walnut
Awarded Mar 12 at 14:15
Making very small mortises/grooves in wood
Awarded Mar 10 at 13:20
What am I doing wrong with white wash pickling stain?
Awarded Mar 9 at 15:45
Is this unit properly supported? [closed]
Awarded Mar 8 at 7:33
Why can't I flatten the back of my mortice chisel?
Awarded Mar 3 at 14:47
White spots after sanding off stain
Awarded Mar 3 at 8:26
Why does my sliding miter saw go slanted down the line instead of straight?
Awarded Feb 29 at 7:55
Securing an Ikea countertop to Ikea drawers (SALJAN and ALEX)
Awarded Feb 25 at 21:41
Are these sanding discs defective?
Awarded Feb 23 at 16:50
How to secure a "basic" butt joint where three pieces of wood intersect? [closed]
Awarded Feb 23 at 1:51
Will splotchy bleached wood stain evenly?
Awarded Feb 21 at 19:27
Is there a parrot grade stain?
Awarded Feb 21 at 8:27
Staining mid to low quality wood
Awarded Feb 17 at 8:35
What would be the best way to unwarp this chess board?
Awarded Feb 3 at 23:16
How to measure correctly?
Awarded Feb 2 at 20:49
Restoring the finish on linseed oil-finished cabinetry
Awarded Jan 22 at 8:27
How to join the broken wooden piece (from a bedside table)?
Awarded Jan 11 at 13:26
Why would a router bit have a spur on it?
Awarded Jan 7 at 16:08
DOL Starter (LE1D12P7) Tripping at end of ramp on table saw [closed]
Awarded Jan 5 at 7:36
Oregon Pacific Jointer
Awarded Dec 16, 2023 at 11:02
Guidance on building a ladder, but not just any ladder
Awarded Dec 13, 2023 at 14:55
Can anyone identify this variety of plywood?
Awarded Dec 9, 2023 at 0:32
How can I find the center of an imperfect circle for a clock face?
Awarded Dec 7, 2023 at 9:48
Yacht varnish to protect antique mahogany veneer? [bathroom vanity]
Awarded Nov 29, 2023 at 9:25
Glue mistake and redo
Awarded Nov 23, 2023 at 9:47
Flattening a maple woodblock by hand for fine art woodcut printing on a press
Awarded Nov 20, 2023 at 9:05
How to route smoothe, diagonal S-shape onto edge of wood board?
Awarded Nov 19, 2023 at 21:01
How to sharpen hand saw with grouped teeth
Awarded Nov 19, 2023 at 14:27
Veneer on 1 vs 2 sides of Baltic Birch ply?
Awarded Nov 19, 2023 at 1:57
Table top uneven stain [duplicate]
Awarded Nov 15, 2023 at 17:03
What is this vise or holder?
Awarded Nov 14, 2023 at 15:15
1
2 3 4 5
…
34