Questions tagged [pi-3b+]
Use for questions specific to the Raspberry Pi 3 Model B+
1,183
questions
0
votes
0
answers
22
views
Unable to connect to RPi AP
I am trying to build my home router using the Raspberry Pi 3B+. I wish to learn more about routers and experiment with them. I am using a Tp-Link AC1300 T3U WiFi Dongle as an external NIC card with ...
-1
votes
0
answers
39
views
RuntimeError: Failed to read data from sensor Raspberry Pi 3B+ With Fingerprint Sensor and Adafruit Library
I am new to Raspberry and I couldn't find anything about this problem.
I am trying to make a smart attendance system with Raspberry and Fingerprint sensors.
While I'm trying to use the basic Adafruit ...
0
votes
2
answers
51
views
Send Ir command with Raspberry pi 3b+ in 2024
Good evening to all guys. I am writing to you because I need help with a project that I would like to carry out and I hope for your help. I'll briefly explain what I'm trying to do.
So via Raspberry ...
0
votes
0
answers
19
views
Raspi-vid - no audio in output - RPI 3, Cam V3, Bullsye
trying to get a rpi-3b+, bullseye, and imx708 to work to provide video AND audio. However, I am just getting video right now:
libcamera invocation:
$ libcamera-vid -t 10000 --width=4608 height=2492 --...
-1
votes
1
answer
28
views
Unable to use UART and Bluetooth in RPi3 with audio output simulatneously
I am using Rpi 3b+ and I am trying to use the Bluetooth and UART simultaneously.
with ls -l /dev:
Serial 0 - ttyAMA0
Serial 1 - ttyS0
I had to use the UART (for reading coordinates in GPS) and ...
0
votes
0
answers
17
views
Blue screen appearing on webcam server of raspberry pi.?
Motion version 4.3.2 is used. If i edit the configuration file according to version 4.1.1 will it work? or is there anyother solution
0
votes
0
answers
26
views
Problem when testing module DAC MCP4922 with Raspberry Pi
I'm encountering an issue while testing a custom-designed DAC module that utilizes an MCP4922 chip as its primary processor.
The vendor provided C language test code for ESP32-S3, but I intend to test ...
0
votes
2
answers
59
views
RPi randomly shutting down, maybe due to GPIO?
I am running a Rpi 3b+ headless, mostly for Pi-Hole now. Nothing external connected, not even a monitor, a mouse or a keyboard.
But because it runs PiHole, and my DHCP clients use it as domain server, ...
0
votes
2
answers
37
views
Latest Pi3B+ board I2S mic and amp does not work
I have tried installing AdaFruit I2S
Speaker and Mic on some newly bought Raspberry Pi 3 Model B Plus Rev 1.4
The install is not working anymore:
The Speaker say it is installed but the sndrpii2scard ...
0
votes
0
answers
21
views
Route all internet to OpenVPN tunnel, allow local traffic, in physical plug-and-play system
I have a raspberry pi and multiple hosts that I would like to connect to a VPN in a physical manner, i.e. I would like to be able to plug my devices into one (unmanaged) switch and have them connected ...
0
votes
0
answers
14
views
Kernel patch for xenomai
I want to have xenomai RTOS on my raspberry pi 3B
The xenomai ipipe-arm patch with rpi-linux as I see the linux version is 6.1.y and ipipe-arm patch does not have latest patch.
I'm trying to patch the ...
0
votes
1
answer
17
views
Can a Pi3 be used as an RS232 to TTL Level Shifter?
I have a couple of Pi 3's here, and have to recover an Iomega NAS. Normally I would use a USB device and have the cables connected from a laptop, run up putty, communicate over the usb serial port to ...
0
votes
0
answers
19
views
Waveshare 13460, GSM HAT doesn't power on
Got this guy waveshare, which stopped powering ON after the first run(which was successful). The power LED is ON, but nothing happens after I press the PWRKEY. I got other identical module which turns ...
0
votes
0
answers
29
views
Broken micro usb solder pads on pi 3 B+
I have picked up these for 6.5 dollars each. Top one is in decent condition i can solder some usb ports and use it but the below one has some issues with micro usb port. Solder pads and traces are ...
0
votes
0
answers
31
views
Why has 64GB SD RPi Bullseye OS card "lost" half it's capacity after opening on PC
I attempted to set up a RP print server using Bullseye(32) on RP 3B+. There were issues that pointed to an i386 problem (...for another day..). I read Bookworm supported i368 so I decided to start ...