Questions tagged [connectors]
Questions regarding the physical electrical connections between the Pi and the outside world, e.g. GPIO, HDMI, USB, ...
48
questions
0
votes
0
answers
33
views
Which Cable Should I Use to Send Serial Data From my PCB to a Raspberry Pi via USB?
My PCB has a 16-pin male connector with a 2.54mm pitch. I was going to connect this to my Raspberry Pi via its GPIO, but I have a PiSound sitting on it now, so my only other option is to connect to it ...
1
vote
0
answers
2k
views
Raspberry Pi 5 Fan Connector Compatibility?
I'm trying to figure out for sure if the Raspberry Pi 5's fan connector is compatible with a Noctua NF-A4x10 5V. The voltage is correct, at least. Now I'm trying to make sure that the board is fine ...
0
votes
0
answers
27
views
Why does my RPI4 not work with a female-to-female HDMI adaptor and HDMI extension cable?
My RPi4 works fine with a micro-HDMI to HDMI cable. But because that cable is too short I have bought a female-to-female HDMI adaptor (coupler) that I use to extend the micro-HDMI to HDMI cable with ...
1
vote
1
answer
144
views
Both 5V pins are taken but I need more [duplicate]
Hi I am doing a project where both 5V pins are taken by a step down connected to a solar panel.
I am using a raspberry 3B and a breadboard.
I need 5V to connect other stuff like ultrasonic sensor etc. ...
1
vote
3
answers
340
views
How to loop audio through a pi for voice change effects?
I want to put a raspberry pi as a voice changer (using sox) between a headset and a game console to add some authentic voice effects for video games.
The raspberry pi needs to loop the audio signal ...
1
vote
1
answer
883
views
RFID card readers with Pi 4
I have been working on an access control project which started out as scanning QR codes using a Pi camera and then triggering a relay using the Pi to open up electro-magnetic locks.
I would like to ...
-1
votes
2
answers
681
views
How would I connect a 4 pin sound sensor to a raspberry pi?
I have a 4 pin sound sensor like this:
How would I connect it to my Raspberry Pi with only wires?
-1
votes
2
answers
310
views
Pi-4 with fans and ribbon cable
New to this. I bought a pi-4 kit. It has dual heatsink fans that get connected to pin 4 and 6. however, I want to do other projects and need to connect a ribbon cable to it. how can i do that while ...
0
votes
0
answers
103
views
Connecting a company embedded camera to Raspberry Pi
I have a proprietary camera that has a 28 pin CSI-2 interface (Connector used in camera - FH41-28S-0.5SH(05) by Hirose). Is there any possibility by which I can interface it to the Raspberry Pi 4 ...
1
vote
2
answers
1k
views
Micro JST 1.25 to any raspberry pi or RPI 4?
I'm Making a raspberry pi project, and I want to connect a Micro JST 1.25 to a raspberry pi.
I already got a Micro JST 1.25 cable, but I need to connect it to a raspberry pi to operate it. I searched ...
3
votes
1
answer
3k
views
RP 4 connecting to Asus ZenScreen monitor issue
I'm very new to RP and I recently bought a new RP 4 and wanted to use a portable touchscreen monitor with it, but I wanted something bigger than the 7-10" ones I saw. I went for this one after a ...
0
votes
1
answer
1k
views
Connecting a Sensirion SPS30 PM sensor to RPi
I am trying to connect the Sensirion SPS30
I'm having trouble connecting it to my breadboard.
This is the connection on the sensor.
I am thinking that I need a 5 pin JST / Molex to plug into the ...
1
vote
0
answers
29
views
What connectors needed to mate Pi4B to KVM switch with video on DB-9 and P/S2 keyboard and mouse?
First off I don't even have a Pi yet, ordered it yesterday.
I've 2 PIIIs on the desktop and a Sony SDM-HS73 display all tied together througn a KVM switch that takes P/S2 connectors for keyboard and ...
2
votes
1
answer
258
views
How to connect harness cable to male pins of Raspberry pi
I have a raspberry pi and omron sensor d6t. This sensor comes with connector in which you can connect harness cable to it. It looks like below:
For my development purpose I connect the wires from ...
2
votes
1
answer
290
views
Connecting DHT11 module kills raspberry
I have a DHT11 module that looks exactly like the image below. I also have raspberry pi zero wh.
I have connected 3.3V (pin1) to the + on the module.
GND (pin6) to the - on the module.
I was carefull ...