Questions tagged [config.txt]
This file is parsed by the GPU before the initialisation of the ARM core. It can be used to set various parameters to alter the behaviour of the system, such as display resolution or overclocking settings.
166
questions
0
votes
2
answers
41
views
PrimeOS 2.1.0 rpi 4b dsi display dont work
Good morning.
I have a dsi touch screen thats works with all distros android on my rpi 4b, but dont work with PrimeOS 2.1.0.
The rainbow appears but after, don't show anything.
All distros android ...
-1
votes
1
answer
37
views
Minimal config.txt for enabling UART0
I am attempting to connect to the UART0 on my Raspberry Pi 4B. I have shorted together GPIO pins 14 and 15 (pins 8 an 10 on the header). I then run picocom /dev/ttyAMA0 and see if it's echoing (it ...
0
votes
1
answer
140
views
When is the 'disable-bt' dtoverlay necessary?
I have a Pi 3B+. There are a number of resources out there that suggest it is necessary to enable the disable-bt overlay in order to make use of the serial UART on GPIO 14 & 15. E.g., this ...
0
votes
0
answers
95
views
Raspberry 4B Composite video issue
Need your help with the Raspberry 4B Composite video issue. I have read official documentation and a lot of topics on the internet, but still did not solve my problem.
Problem:
I power Raspberry ->...
0
votes
1
answer
70
views
480x320 display HDMI - blank after boot
I am trying to get to work mini HDMI chinese 480x320 display.
I want to display only console output, and that resolution is good enough for it.
Display is known to be ok, during boot it shows good ...
0
votes
0
answers
41
views
rPi 4 two screen configuration without the gui
I tried plugging two screens with different dimentions into this pi4 and the result is a mess. What is more, I started with PiOS 64 lite, and am running the i3 desktop. Loving i3, but of course ...
1
vote
1
answer
585
views
What filename does auto_initramfs look for?
From the config.txt documentation:
If auto_initramfs is set to 1, look for an initramfs file using the same rules as the kernel selection.
Presumably it's looking for something with either no suffix,...
1
vote
0
answers
596
views
Configuring the Raspberry Pi 4 B as a USB (HID) Gadget?
I am new to Raspberry Pi and recently got a RB Pi 4 intending to use it as a mouse/keyboard for my laptop. The problem is that I can't find valid information about how to configure the Pi 4 as a USB ...
1
vote
0
answers
666
views
Updating RaspberryPi Ubuntu Server 20.04 to 22.04 caused usercfg.txt to not be honored
I asked on askUbuntu a while back but didn't get much traction... should have known there was a stack for Raspi...
So I've been putting my HMDI output configuration in /boot/firmware/usercfg.txt
...
0
votes
1
answer
195
views
raspberry 400 hdmi output does not follow config.txt
Have my new raspberry 400 with current Raspberry OS and connected a TV by the official micro-HDMI-cable. There is no problem getting an image, but it always goes to 1080p@50 mode (TV tells me that, ...
0
votes
2
answers
37
views
MAX31586 configuraiton using overlay
I want to read three MAX31586s using a Raspberry pi 3B.
Two are connected on the spi0 and I can configure the maxtherm on config.txt to work. For the third one, maxtherm doesn't work with spi1, at the ...
0
votes
0
answers
85
views
Cannot set MAC address for Pi Zero W USB ethernet gadget
I am trying to create a portable debian system that runs on pi zero w using the 0W image from debian-downloads, I downloaded the image and flashed it to an sd card using etcher.io, next I edited ...
0
votes
1
answer
264
views
4K video Stuck in raspberryPi4 (8GB RAM) even after doing required settings of config.txt
i am stuck at playing the 4K even at less frame rates (25fps) on the HMDI 0/1 of my raspberryPi4 (8GB,Cortex A7 CPU,1.5Ghz CPUspeed) even after desirable settings of raspi4 and being supported by the ...
1
vote
2
answers
203
views
Turn on raspberry PI from an input GPIO pin without ground
For context, I am using a raspberry PI 4 connected with it's charger (edit : I meant power supply, not charger). I wish to be able to turn it on when it receive a high value on a pin (for example,...
-1
votes
1
answer
1k
views
Parameter order in config.txt - Can't change screen resolution
Does the order of the parameter in the config.txt matter? For example if hdmi_cvt=800 400 60 6 0 0 0 specified before the parameters (hdmi_group=2 & hdmi_mode=87) that specify that a custom ...